square washers for sale, brand-new and used.

THREE Fiber washers for meat grinder augers. This is made for Hobart, Biro, Berkel, Cabelas, Universal, and all commercial grade meat grinder augers. Will fit your auger if it has the 3/4" square end.

used 3 by 3 inch galvanized square washers to hold insulation board plywood etc 0.25 inch diameter screw hole metal is 1/32 thick; plate is stamp reinforced; so is actually a 3/32 inch thick plate overall. weight about 1 oz each

5/8 Grade F436 Square Bevel Hard Washer Hot Dip Galvanized, Pk 250 Item Description: Square Bevel Hard Washer Size: 5/8 Type:

Each set contains: 9-70 bushing 9-73 sleeve bolt washer nut This listing is for ALL THREE SETS. All three sets are used and have typical wear, but are ready to use and 100% functional. I used them myself on my 10" Atlas lathe that I am parting out.

Up for auction is a Ramset RS22, .22 caliber single shot tool, trigger operated powder actuated tool. Included with the tool are three(3) boxes of Remington Power Fasteners, Square Washers, One(1) box of Remington Power Fasteners, ACQ Plus, 3/4"(19mm) DUO-FAST fasteners, attaches track to concrete, and five(5) boxes of .22 caliber powder loads. You can look at the color of the boxes in the photos and match them with the color chart at the bottom of the listing.

var itemNumber = window.ebayItemID ?

var itemNumber = window.ebayItemID ?

var itemNumber = window.ebayItemID ?

ALL 3 PIECES WERE DISASSEMBLED AND CHECKED ALL 3 HAVE GOOD TANGS FOR SCALE SLOT THREADS, NUTS WASHERS ALL INTACT AS ORIGINAL SQUARE HAS GOOD LEVEL VIAL BUT SCRIBER IS MISSING. LITE TARNISH, MINOR DINGS, DISCOLORATION, AGE MARKS ETC. ON ALL THREE GOOD SCALE W/ 4 GRADS ALL COULD USE A CLEAN-UP LITE CRUD IN SLOTS "KELLY" LITELY ETCHED ON SCALE AND C/HEAD.

This listing is for a Andrew Type 64757-137 Hardware kit - (cover / gasket) (WR137), new in a sealed bag, (with two additional rubber gaskets attached to the outside by stapling the corner of the plastic bag through the gaskets). The kit includes the two extra square rubber gaskets mentioned, two round rubber gaskets inside the kit, six each ss screws, nuts and flat washers, and an allen wrench to tighten the screws.

Disconnects are in great condition, 3 phase fusible, 30 amp rated for 600 volts

1/2x1/2x.195 Square Plate Washer Steel / Hot Dip Galvanized Pk 25 Item Description: Square Plate Washer Size: 1/2x1/2x.195 Type: USS (Large Diameter)

This listing is for a lot of 2 wire baskets that I believe are used in lab glassware washers. 16-1/2" x 16-1/2" x 3-1/2". The square hole in the middle is just slightly less than 2-1/2" x 2-1/2".

ONLY TWO PIECES ARE MARKED. TWO PAIR OF STEP BLOCKS ARE "NORTH WESTERN TOOLS OHIO" & ONE PAIR OF STEP CLAMPS ARE "TIETZMANN TOOL CO. OHIO".

BEST VIEWED USING GOOGLE CHROME BROWSER MAX 1618 A/B 96.0 FLUID OUNCE COMBINED VOLUME 1/2 Gallon MAX 1618 PART A (HALF GALLON 64 FL.OZ) AND

This Is a Ball Muffler For the 1 & 1 1/2 Hp Hit & Miss Gas Engines Using A 1" Pipe Thread For the Exhaust. This is very similar to the Ball Mufflers that were used on the various Early Hit & Miss Gas Engines Like Sparta Economy Waterloo Galloway Associated Etc.. This is 7" In Dia .....

The table support cleats and hardware for a DeWalt 7730 or 7740 radial arm saw. Part numbers 72091, 72091-01, 84180, 72086, 81911 The two support brackets, two table clamps, four square headed bolts, four of those over sized DeWalt nuts and the original washers.