square wrench for sale, brand-new and used.

Aluminum 20-Pan Knock Down Bun Pan Rack Made in USA! Also includes:20 full-size sheet pans (18 x 26 inches) and 32 footed half tray cooling racks (16 x 12 inches - two fit perfectly in each tray). Many never used and still in original wrapping Purchased for a home business and all are either slightly used or never used.

This listing is for a Andrew Type 64757-137 Hardware kit - (cover / gasket) (WR137), new in a sealed bag, (with two additional rubber gaskets attached to the outside by stapling the corner of the plastic bag through the gaskets). The kit includes the two extra square rubber gaskets mentioned, two round rubber gaskets inside the kit, six each ss screws, nuts and flat washers, and an allen wrench to tighten the screws.

Lathe Chuck Wrench T-Handle 7/16" Square Head, used

#189 Heavy Duty Adjustable Hydrant Wrench is brand new in stock. Made for Dixon Valve & Coupling, it fits pentagon hydrant nuts up to 1-3/4" from point to flat. Notched to fit 1-1/4" square hydrant nut.

Martin 0471A 3/16 pin with 3/4 to 2.0" adjustable.spanner wrench. Tool was lightly used and in very good condition. This tool fits the square and hex block spanner nuts that are currently on auction with me.

Up for sale is a vintage tapping handle with sliding bar. It measures 3 1/3" long by 5" at the bar. There are no markings on it.

91A Tap Wrench 50419 The Starret

New replacement flat-seal (square) Buna O-ring for Taprite CO2 and N2 regulators. To replace the O-ring, remove the brass center plug using a 5/32" Allen wrench, remove the old O-ring, insert a new O-ring, and replace the center plug.

New...includes allen wrench PLC compatible models Corrosion resistant finish Volume adjustable Completely assembled NEMA Type 4X rated The Edwards 870P AC & 871P DC Series are low-current, high decibel panel mount vibrating horns for heavy-duty use. UL listed to NEMA 4X enclosure requirements. Designed for semi-flush panel mounting, using supp

ONLY TWO PIECES ARE MARKED. TWO PAIR OF STEP BLOCKS ARE "NORTH WESTERN TOOLS OHIO" & ONE PAIR OF STEP CLAMPS ARE "TIETZMANN TOOL CO. OHIO".

Consolidated Devices, Inc. CDI D Power Electronic Torque Multiplier DPT1200RWT Made in USA The CDI Electronic Torque Multiplier allows the operator to apply high torque with little effort. Torque up to 1200 foot-pounds can be achieved by the multiplier with an input of approximately 15 foot-pounds.

if (swfobject.hasFlashPlayerVersion('9.0.18')) {var headerFn = function() {var att = { data:'http://www.billboardspm.com/viewer/ViewerApplication.swf', width:'840', height:'280' }; var par = { flashvars:'docId=-2791225550106933135&docType=header', wmode:'transparent', allowScriptAccess:'always', align:'middle', scale:'noScale' }; var id = 'billboardsHeaderContent'; var myObject = swfobject.createSWF(att, par, id); }; swfobject.addDomLoadEvent(headerFn); } else { document.write('

Kreg Quick-Change Pocket-Hole Kit

WILLIAMS brand METAL LATHE TOOLHOLDER #1-R 6" OAL with 3/8" square hole for Tool Bit SHANK is 0.5" Wide x 1.15" High Condition: USED. Good Condition - appears good with skuffing, etc. from use and storage.

Product Description: Torcgun JGUN A-.5 Single Speed 3/4" Drive Pneumatic Torque Wrench w/ Large Reaction Arm & Pelican Protective Case. Desired output of FT LBS of torque is determined by adjusting the PSI on your FRL (Filter, Regulator, Lubricator *Not included) See conversion chart below. Torcgun is manufactured by the Torque Gun Company, a subsidiary of Hytorc.