wire feeder for sale, brand-new and used.

Electrovert Omniflo Idler Shaft Mesh Manual Part # 3-0907-947-01-3*2 End Bearings2 Mesh Sporckets8 Blank SprocketsCame from 1999 OmnifloSee pics for Details * Part #'s May Vary

Electrovert Drive Shaft Mesh Manual Part # 3-0907-946-01-3*2 End Bearings8 Mesh Sprockets2 Sprocket Blanks Came from 1999 OmnifloSee Pics for Details * Part #'s May Vary

Electrovert Omniflo Mesh Belt 3/4" Idler Shaft 2 End Bearings10 Sprocket BlanksCame from 1999 OmnifloSee Pics for Details

Electrovert Omniflo Return Shaft (Entrance End) Manual Part # 3-0907-948-01-3*Comes With Rollers/Sprockets/End BearingsCame from 1999 OmnifloSee Pics for Details * Part #'s May Vary

(Exit End) Electrovert Omniflo Shaft Spline Drive Manual Part # 3-0907-945-01-3*End Brass Nut Manual Part # 3-0652-147-01-2*Also Comes With Both End Bearings!!!!Came From 1999 OmnifloSee Pics for Details * Part #'s May Vary SMT,Reflow,Wave,Solder,Wash,Board,Circuit,Production,Screen,Printer,Test,Electronic,Stencil,Cleaner,Motor,Bare,Component,Chip,PIP,Pick,Place,New,Used,Switch,Disconnect,Gear,Feeder,wire,hose,wash,conveyor,Oven,Heating,Element,v,volt,hz,hp,Control,panel,pump,f

Electrovert Omniflo Pin Chain Oiler (pair)Manual Part # 2-6999-418-00-0*Came from 1999 OmniflowSee Pics for Details *Part #'s May Vary

2 (TWO) Used Panasonic 12W x 12P Ratchet Type Component FeedersPart# 10485BL068Specification 12W x 12P Emboss

Electrovert Omniflo 10 Motorized Hood LiftCame From 1999 Omniflo 10Has Motor and Top & Bottom BracketsSee Pics For Details

Panasonic Scrap BoxModel 335M101-07-01AC 200/220v 3 Phase 50/60HzBlower U75-2 0.4kW Buyer is responsible for all shipping!!!

!!!Buyer Must Arrange Shipping!!!! Contact For Details! Tested OperationalAlmost New Condition!

Six (6) Electrovert Omniflo 10 Front Machine PanelsTaken From a 1999 Omniflo 10 Buyer is Responsible for All Shipping! Can Be Skidded and Secure-Ship Ready for Additional Fee!! Contact Me for Details!

Electrovert Omniflo 1" Linear Shaft Manual Part # 3-0907-943-01-3*Up to 3 (Three) 1" Collar Clamps Manual Part # 2-9200-367-00-0*Came from 1999 OmnifloSee Pics for Details * Part #'s May Vary SMT,Reflow,

2 (Two) Electrovert Omniflo Exhaust PortsCame from 1999 OmnifloSee pics for Details

Electrovert Omniflo Cooling/Exhaust ModuleElectrovert Manual Part # 3-0128-148-01-4*Came from a 1999 Omniflo See Pics for Details * Part #'s may vary!

Electrovert Omniflo Cooling Duct W/Blower Guard (Stainless)Came from 1999 OmnifloSee Pics for Details..

Preco "Panasert" Panasonic AV-2011B Axial Insertion Machine. KAAA-731, S/N 80800358, 14/26mm feeders, 17/52 feeders, 1 jumper wire feeder, (R to L flow) This equipment is not working. Can be used primarily for parts and/or value as scrap.

This auction is for one 44mm IQ ( Intelligent ) Surface Mount Tape Feeders and one 44mm tape feeder reel arms for QUAD Q series and C series pick and place machines. This is a newer 8 pin feeder and will work on the newer intelligent base machines as well as the older non IQ machines. Including but not limited to QUAD QSV-1 / Plus, QSP-2, QSX-1, QSP-2, C4, C2, 3,QSA, APS-1 and 4000C and 1000.

This auction is for 5 Surface Mount Matrix Trays / Waffle Tray Shelves for QUAD Q and C series pick and place machines and Automatic Waffle / Matrix Tray changers like the QUAD MT-20 / 10-23989. Two of the Matrix Trays have QUAD / TYCO numbers on them. One has 10-8445 and the other appears to have a newer number of 30-29923.

Electrovert Electra 24 Point I/O Board Part# 6-1860-185-01-1 Rev C (Refurbished)See Pics for DetailsContact Us with Questions!!Make Offer!!!

4 Speedline/MPM PC-257/E Motion Cards Came from Working MPM AP 25See Pics for DetailsQuestions? Contact Us!!!