+ Post new Ad
woodtek 21 inch drill press w/ mortising attachment + 3 & 8 inch craftsman vises, US $2600 – Picture 0
woodtek 21 inch drill press w/ mortising attachment + 3 & 8 inch craftsman vises, US $2600 – Picture 0

Woodtek 21 Inch Drill Press W/ Mortising Attachment + 3 & 8 Inch Craftsman Vises

US $2600

  • Bessemer, Alabama, United States
  • Jun 11th
Open on mobile:
QR code
Woodtek 12 Speed 21 inch Drill Press - 1 HP Model 816812 Like  new  -  unused  -  12  Speed  Woodtek  21  inch  Drill Press  as  per  pictures: 1)  Front 2)  Right Side 3)  Left Side 4)  Back 5)  Top  / Drive, Driven  &  Idler Sheaves 6)  Close  up of  Base  &  Table  with (3)  prong  plug 7)  Motor  / Chuck 8)  Woodtek Mortising  Attachment  w/  bushings  and  chisels  & Chuck  Key 9)  Speed  Chart  /  Table  tilt  label  /  Power &  Light Switch 10) Accessories: Craftsman 8 inch vise - 924077 Craftsman 8 inch vise pipe jaws - 924099 (inset photo)  Craftsman  3  inch  angle  vise  -  924083 11) Owner's Manual Drill  speeds  are  180  -  4200  RPM  with  a  1  HP  4 pole  12 AMP  1700  RPM  single  phase  120 VAC  60 Hz.  motor.    The  table  can  tilt  45  degrees left or  right of center.   The  chuck  can  except  up  to 5/8 dia. bit  shank.   The  swing  is 21-1/8 inches &  the  stroke  is  4-13/16 inches.   The  chuck  arbor  is JT3/MT3  taper.    The  machined  portion  of the  table  surface  is  13-5/8 x  16-1/4 inches.    The mortising  attachment  has  chisel sizes  of  (inch):  1/4,  5/16,  3/8, 1/2  & 3/4.    Both craftsman  vises are  new and  unused.   The  8 inch  vise  comes with  a  set of  prismatic  jaws.   These  jaws allow  for the  secure  clamping  of pipe  or round  stock  while  drilling.    The  press  was purchased  new  on 6/02  from Woodworkers  Supply.   Save a  little  dust  on  the  machine  and  some  stains on  the  front of the press base, the unit was never put into service. Payment  method  is  PayPal.   Refund  or  Return  not  possible.   Local  pickup  only  with assistance available  for loading.   The  assistance  is  in  the  form  of a manual overhead  hoist  on  steel frame.  The  buyer  has 36  hrs  to  pay or  the  press will  be  relisted  & has 48  hrs after payment to take delivery  or payment  will  be refunded.   The  press is  at  a  residence.   There  is  sufficient  room  for (1) passenger  vehicle,  truck  or car, with  pull behind  trailer.   The  trailer length  cannot  exceed  16  ft.   There  is  NOT  room  for  fork  trucks  or other powered  material handling  equipment.   The  unit  has a  net  weight  of  326  lbs.  with  overall  dimensions (inches):  69 Tall  x  34  Deep  x  20 Wide.

Directions

Similar products from Drill Presses & Spare Parts

Clausing 20" Variable Speed Bench Mount Drill Press 1.5 HP Model 2282-300

Clausing 20" Variable Speed Bench Mount Drill Press 1.5 HP Model 2282-300

  • Venice, Florida, United States
  • Jun 15th
Black and decker drill press stand used

Black and decker drill press stand used

  • Albuquerque, New Mexico, United States
  • Jun 15th
Ganner Red Baron Type 204 Gannomat Wood Working Machine 220V 1PH

Ganner Red Baron Type 204 Gannomat Wood Working Machine 220V 1PH

  • Chandler, Arizona, United States
  • Jun 14th
Boice Crane 15" Drill Press Table

Boice Crane 15" Drill Press Table

  • Flushing, New York, United States
  • Jun 14th
Walker Turner 15" # 900 Drill Press Head Quill Lock Lever Handles

Walker Turner 15" # 900 Drill Press Head Quill Lock Lever Handles

  • Flushing, New York, United States
  • Jun 14th
Delta Spindle 5140029-54

Delta Spindle 5140029-54

  • Somerville, Tennessee, United States
  • Jun 14th
DELTA ROCKWELL 15 DRILL PRESS 15-090 SP 450 - 1950 RPM 7-1/2" Swing TOP BENCH

DELTA ROCKWELL 15 DRILL PRESS 15-090 SP 450 - 1950 RPM 7-1/2" Swing TOP BENCH

  • Naperville, Illinois, United States
  • Jun 14th
32" Walker-Turner Radial Arm Drill Press 18 x 26" Table, 1/2 hp, 3ph 220v

32" Walker-Turner Radial Arm Drill Press 18 x 26" Table, 1/2 hp, 3ph 220v

  • Del Rio, Texas, United States
  • Jun 13th
Craftsman Drill Press Vintage 1/3 H.P. Ball Bearing Heavy Duty +" PICK UP ONLY +

Craftsman Drill Press Vintage 1/3 H.P. Ball Bearing Heavy Duty +" PICK UP ONLY +

  • Henderson, Nevada, United States
  • Jun 12th
Walker Turner 15" Drill Press Table 2 3/4" Column

Walker Turner 15" Drill Press Table 2 3/4" Column

  • Long Beach, California, United States
  • Jun 12th
Delta Drill Press 14-070 Floor Standing 14" Very Nice Pre Owned

Delta Drill Press 14-070 Floor Standing 14" Very Nice Pre Owned

  • Hawaiian Gardens, California, United States
  • Jun 11th
Vintage Delta Rockwell Drill Press COMPLETE HEAD DP 220 2 3/4" COLUMN

Vintage Delta Rockwell Drill Press COMPLETE HEAD DP 220 2 3/4" COLUMN

  • Hamlet, Indiana, United States
  • Jun 10th
TANNEWITZ 36" VERTICAL BAND SAW

TANNEWITZ 36" VERTICAL BAND SAW

  • Berkeley, California, United States
  • Jun 9th
Kanetec magbore mini type kcd-mn1 model drill press

Kanetec magbore mini type kcd-mn1 model drill press

  • Philpot, Kentucky, United States
  • Jun 9th
13" Delta Drill Press w/ Albrecht Chuck 0-3/8"

13" Delta Drill Press w/ Albrecht Chuck 0-3/8"

  • DeKalb, Illinois, United States
  • Jun 9th
POWERBOR REVO Magnetic Drill Press

POWERBOR REVO Magnetic Drill Press

  • Flushing, New York, United States
  • Jun 9th
Drill press laser pointer

Drill press laser pointer

  • Burnsville, North Carolina, United States
  • Jun 9th
Blum ECODRILL for Clip Top, Modul, Avento Hinges M31.1000 Boring Bits Included

Blum ECODRILL for Clip Top, Modul, Avento Hinges M31.1000 Boring Bits Included

  • Suffield, Connecticut, United States
  • Jun 9th
Delta DP 220 Drill Press 14" inch DP220

Delta DP 220 Drill Press 14" inch DP220

  • Francis Creek, Wisconsin, United States
  • Jun 9th
POWERMATIC DRILL PRESS #1150 PARTS "BASE"

POWERMATIC DRILL PRESS #1150 PARTS "BASE"

  • El Paso, Texas, United States
  • Jun 9th

People who viewed this item also vieved

Nova Dvr 3000 Wood Lathe

Nova Dvr 3000 Wood Lathe

  • Hollywood, Florida, United States
  • Jan 30th
Craftsman/Atlas 8" Face plate

Craftsman/Atlas 8" Face plate

  • Emporia, Kansas, United States
  • Jan 30th
Delta 1460 Lathe Headstock Cover

Delta 1460 Lathe Headstock Cover

  • Northwood, Ohio, United States
  • Jan 30th
Hoffmann PP-2 TAB/4 Dovetail Routing Machine **BRAND NEW**

Hoffmann PP-2 TAB/4 Dovetail Routing Machine **BRAND NEW**

  • Bonita Springs, Florida, United States
  • Jan 30th
2014 Vitap Smart 3 Contour Edgebander...BRAND NEW...Warranty

2014 Vitap Smart 3 Contour Edgebander...BRAND NEW...Warranty

  • Sauk Rapids, Minnesota, United States
  • Jan 30th
Hoffmann PP2-VH Dovetail Routing Machine **BRAND NEW**

Hoffmann PP2-VH Dovetail Routing Machine **BRAND NEW**

  • Bonita Springs, Florida, United States
  • Jan 30th
Nr. 350 3D MODEL RELIEF STL VECTRIC RLF ARTCAM MODEL FOR CNC ROUTER MILL

Nr. 350 3D MODEL RELIEF STL VECTRIC RLF ARTCAM MODEL FOR CNC ROUTER MILL

  • Vilnius, Lithuania
  • Jan 30th
Nr. 124 3D MODEL RELIEF STL VECTRIC RLF ARTCAM MODEL FOR CNC ROUTER MILL

Nr. 124 3D MODEL RELIEF STL VECTRIC RLF ARTCAM MODEL FOR CNC ROUTER MILL

  • Vilnius, Lithuania
  • Jan 30th
NSK C5 ground ballscrew 15-10mm L560mm Travel 455mm BALL SCREW

NSK C5 ground ballscrew 15-10mm L560mm Travel 455mm BALL SCREW

  • China, China
  • Jan 30th
STATE MODEL # S3 OSCILLATING SPINDLE SANDER TABLE - MASTER KINDT COLLINS OLIVER

STATE MODEL # S3 OSCILLATING SPINDLE SANDER TABLE - MASTER KINDT COLLINS OLIVER

  • Seattle, Washington, United States
  • Jan 30th
Sanding Master CSB 2-600 23" Belt

Sanding Master CSB 2-600 23" Belt

  • Island Falls, Maine, United States
  • Jan 30th
STATE S-3 OSCILLATING SPINDLE SANDER - THROAT PLATE / TABLE INSERT - USA

STATE S-3 OSCILLATING SPINDLE SANDER - THROAT PLATE / TABLE INSERT - USA

  • Seattle, Washington, United States
  • Jan 30th
Comet woodworking saw Radial Arm round ram 12 inch

Comet woodworking saw Radial Arm round ram 12 inch

  • DeKalb, Illinois, United States
  • Jan 30th
Omga RN600 woodworking Radial Arm saw 24 inch stroke 600 p3s

Omga RN600 woodworking Radial Arm saw 24 inch stroke 600 p3s

  • DeKalb, Illinois, United States
  • Jan 30th
Schelling FW-430 CNC Panel saw

Schelling FW-430 CNC Panel saw

  • Anderson, Indiana, United States
  • Jan 30th

By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.

Accept All Cookies