30mkv-100v 0.1-0.001mks Pulse Oscilloscope Calibrator I1-9 An-g Agilent

US $850.00

Lviv, Europe, Ukraine
Jan 29th

Open on mobile:
QR code

High precision Pulse oscilloscope calibrator I1-9 analog of Lutron, Advantest, Avtech, HP Agilent, NoiseCom, General Radio, Boonton, Anritsu, Fluke and general Electric, but has the same or better characteristics. This device can be used for wide measurement range. Is designed for oscilloscopes testing and calibration with 100 MHz bandwidth. Signal form - positive polarity rectangular pulses Amplitude 30 * 10-6 -100 V with discrete setting Uk = (lm * 10n)V, where l = 3, 4, 5, 6, 8, 10; n = -5, -4 -3, -2, - 1, 0 Calibration setting mode error (at load 1 MOhm) ± 2.5 * 10-3Uk 3 mkV Pulse oscilloscope calibrator I1-9 is designed for oscilloscopes testing and calibration with 100 MHz bandwidth (variations coefficient and transient response channels of vertical deviation). Calibrator can be used to improve accuracy and reliability of metrological oscilloscope measurements. Calibrator meets requirements of GOST 22261-82. Devise pulse oscilloscope calibrator I1-9 using conditions: - Ambient temperature in operating conditions of 278 to 313 K (of 5 to 40 ° C); - Ambient temperature in extreme conditions of 223 to 333 K (of -50 to +60 ° C); - Relative humidity up to 95% at 303 K (30 ° C); - Voltage supply (220 ± 22)V, frequency (50 ± 0.5) Hz, (115 ± 5.75) and (220 ± 11) V, frequency (400 ± 10) Hz. Condition: NEW (not used, an old stock). Tested and 100% workable. If necessary, we can provide calibration certificate from Government standardization institute (+145-265usd). Also we can provide other resistance, capacitance and inductance standards, decade box and other etalons. Also we can provide other resistance, capacitance and inductance standards, decade box and other etalons. Please take a look on my other items! If you haven’t found the needed item in my listing, please contact me. I’ll try to help you. Technical characteristics of devices Calibrators I1-9: Pulse oscilloscope calibrator I1-9 shows calibration signal coefficient deviation oscilloscope vertical position channel of the following types: - rectangular pulses ("square wave") positive polarity, repeat frequency 1 kHz ± 10%; - rise and fall time is less than 10ms (peak no recession); - positive DC voltage; - negative DC voltage; - zero voltage. Calibrator provides voltage Uk oscilloscope vertical deflection calibration deviation channel coefficient at the end of 1.5-meter 50-Ohm cable, loaded at resistance 1MOhm ± 5%, big ripple and noise, do not exceed 10-3 Uk + 5mV. Calibrator provides voltage Uk calibration deviation channel coefficient oscilloscope vertical deflection at the end of 1.5-meter 50-Ohm cable, loaded at resistance 1MOhm ± 5%, in amplitudes range from 30 mV to 100V. Pulse oscilloscope calibrator I1-9 provides setting deviation Dn value - voltage calibration coefficient deviation channel oscilloscope vertical deflection in deviation mode in range ± 3% and ± 10% from voltage calibration mode with an absolute installation accuracy, not exceeding normal ± (2.5 • 10-2 Dn + 0.06%) in deviation range ± 3% and ± (2.5 • 10-2Dn + 0.3%) in deviation range ± 10% and not exceeding in working conditions ± (3.5 • 10-2Dn + 0.06%) in deviation range ± 3% and ± (3.5 • 10-2Dn + 0.3%) in deviation range ± 10%, which determines absolute error of voltage calibration coefficient deviation channel oscilloscope vertical deflection in deviation mode. Calibrator I1-9 shows oscilloscope periodic calibration signal duration sweep (with deviation of repetition period Tk), whose parameters at the end of 1.5-meter 50 Ohm cable, loaded on resistance 50 Ohm ± 5%, meet the following requirements, polarity is positive; scale is not less than 1V, range set repeat period from 100 ns to 10 s. Calibrator I1-9 provides deviation Dn set, following period of calibration signal oscilloscope sweep duration (with deviation of repetition period Tk) in deviation mode range ± 3 and ± 10% from repeat period in calibration mode with an absolute accuracy, which do not to exceed in normal conditions ± (2.5 • 10-2Dt + 0.06%) in deviation range ± 3% and ± (2.5 • 10-2Dt + 0.3%) in deviation range ± 10% and do not exceed operating conditions ± (35 • 10-2 Dt 0.06%) in deviation range ± 3% and ± (3.5 • 10-2 Dt + 0.3%) in deviation range ± 10%, which determines absolute error of repeat period of calibration signal oscilloscope sweep duration (with deviation of repeat period Tk). Isolation circuit input main connector - case calibrator maintains with no breakdown AC test voltage (rms) 1500 V, frequency 50 Hz under normal conditions and 1000V test for moisture resistance. Insulation resistance of calibrator circuit relative to case is at least 100 MOhm, with high humidity of not less than 5 MOhm, at elevated temperature is not less than 5 MOhm. Pulse oscilloscope calibrator I1-9 provides its technical characteristics within established norms after 15 minutes self-heating time. Calibrator retains its technical characteristics within prescribed standards in its power from AC voltage (220 ± 22)V, frequency (50 ± 0.5) Hz and harmonic content up to 5%, as well as voltage supply (115 ± 5.75)V and (220 ± 11)V, frequency (400 ± 12) Hz. Power consumed by calibrator at nominal voltage, do not exceed30V • A. Pulse oscilloscope calibrator I1-9 allows continuous operation under operating conditions for 8 hours while maintaining its technical characteristics within established norms. Industrial radio interference voltage shall not exceed 80 dB at frequency from 0.15 to 0.5 MHz, 74 dB at frequency from 0.5 to 2.5 MHz, 66 dB at frequency from 2.5 to 30 MHz. Radio field intensity should not exceed 60 DB at frequency from 0.15 to 0.5 MHz, 54 dB at frequency from 0.5 to 2.5 MHz, 46 dB at frequency from 2.5 to 300 MHz. Calibrator mean time between failures is at least 10000 hours. Calibrator gamma-percent life is 15 years in ? = 80% average life 10000 hours. Calibrator I1-9 at customer request can have a built in service time counter capacity - is not less than 2500 hours. Dimensions - 360x210x245 mm. Weight - 7 kg. Warranty 12mounth. Delivery term This device is available in stock right now. I can send it at one day after your payment. But due to the fact, that this device is of high precision, it should be calibrated before shipping. I calibrate and test all my devices. Calibration time may take from 1-14 days. (depends on device, usually it takes 3 days.). I can send it at one day after your payment but without any calibration. Please chose. I can supply you such device of fresh years of manufacture 2011-2012, but the price of such device will be approximately 20-40% higher or more. This device also can be named as: I1-9, I19, I1 9, ?1-9, ?1 9, ?19. Photos If necessary we can take photos of a device from various angles. Technical Documentation In case you didn't find in technical specifications for the device all necessary information you are interested in, feel free to contact me. I will look through the technical documentation for the device and I will be happy to consult you. Also I may speak directly with the manufacturer and find out more specific information about this product. If some technical parameters for the device (error, accuracy, measuring range, operating voltage and frequency) do not meet your requirements, please, e-mail me and I will negotiate with the manufacturer whether it is possible to deliver you a device on the desired specifications without a cost increase and in the shortest time. On delivering the device, electric circuit diagrams and all technical documentation for operation, calibration and maintenance will be supplied. Also there will be documents that testify the accuracy and compliance with specifications. In addition, translation of technical documentation into the customer’s language may be discussed. Delivery set On delivering the device will be completely ready for use. There are all necessary cables, adapters, sensors and spare parts as envisaged in technical documentation. Hence, there is no point in purchasing any additional repair & measurement equipment. Warranty Warranty of this item - 12 month. Before sending a device, all devices are checked whether they comply with all technical specifications. Highly qualified metrology engineers carry out the check-up of every instrument at a specialized laboratory and with the help of master gages. If necessary, we can send you photos or video with the check-up process. I ship only fully working devices complying with all parameters. The warranty for this device is 1 year from the date of shipment from my warehouse. Within 1 year term I will provide the repair of the device for free in case of manufacturing defect or when the technical parameters do not comply with technical documentation. You will have to pay only for delivery. When a device is out of order due to your fault (its fall, it is flooded with water, the power supply does not meet the specified technical requirements, input signals exceed the norm, etc.) or there are conspicuous marks of casing opening (broken warranty labels), it is considered a non-warranty repair. Within 1 year term we can advise you for free on the device operation. After-warranty service After warranty termination I can arrange a paid repair and technical maintenance of a device as well as I can sell you all necessary spare parts for repair at minimum prices. I always have them in stock. Packaging Immediately after checking, the device will be wrapped in several layers of strong air-bubble film and placed into a strong cardboard box. Extra cardboard plates will be used for fixation. If necessary, wooden box or pallet may be used. For a more reliable fixation foam can be applied. The whole box will be placed in a waterproof polyethylene bag which will be wound with several layers of packing tape. A special handle will be made for ease of transportation. Thus, I guarantee qualitative and conscientious packing of the device that reduces to minimum the possibility of damage during transportation. Discount (from-10% to -90%) I suggest you a device which is unique in its class and price category with the following specifications: (accuracy, measurement range, error, temperature operating conditions), endurance and durability (military performance, aluminum, stainless steel, titanium or carbolite casing, shock and vibration resistance, high maintainability and reliability), free measuring kit (cables, adapters, load, fuses, etc.), 1year warranty. Unused cheap devices with the same specifications, accuracy and durability do not exist. If you consider the price for this device unreasonably high, and you know the similar equipment at a lower price, please, let me know. I will help you to compare these two models. In case your model (which is cheaper) is the same as the device I suggest or even it is better, then I guarantee to sell you a unit at that cheaper price with additional 10% discount. Shipping details: Please, mind that I ship from Ukraine (Europe, +2), so that the shipping time may differ from your local time. I send goods via AirMailpost. App. delivery time : Europe – 7-15 days; USA, Japan&others – 10-2days (depends on a country). I will ship in 2-3 business days after payment clearance. The goods may also be delivered by the express mail services such as DHL, UPS, FedEx, TNT or EMS. With express delivery you will mostly receive your goods within 3-7 working days. Payment details: I expect payment in 4 days after the auction ends. I accept a PayPal payment as the safest way of payment (preferably). If you do not have a PayPal account you can pay by wire transfer to my credit card. Other variants of payment are acceptable, for example in case of pickup way of shipping, i can accept cash payment. (This will be an official purchase on eBay). Please, tell me if you cannot pay in time, we can always negotiate it. When purchasing a few items, you’ll save on shipping. Return policy: I accept refunds and returns. If there is something wrong with the device, please, inform me within 5 days after receiving it. I will refund your costs or send you the other item, as you wish (after I receive the previous item). Please only serious bidders!

Condition:	New other (see details): A new, unused item with absolutely no signs of wear. The item may be missing the original packaging, or in the original packaging but not sealed. The item may be a factory second or a new, unused item with defects. See the seller’s listing for full details and description of any imperfections. ...	Brand	I1-9
MPN	I1-9
Model	I1-9