31 200 for sale, brand-new and used.

Used Shizuoka CNC Milling Machine. Non-working good for retrofit. It does not include servo motors.

Item#3962 Astec Model CDH-2A Hole Popper Equipped With: Machine Specifications: Work table, (260 x 314 mm) 10.2" x 12.3" Work table height, (54.5 mm) 2 9/64" Work tank, (368 x 463 mm) 14 31/64" x 18 15/64" Maximum work piece height, (240 mm) 9 29

Thousands of Used Metalworking and Plastic Machines & New Machine Tools Photos, Full Descriptions and Prices - Fast & Easy

Machine Introduction

Machine Introduction The filling machine is our most strength equipment. It is made from stainless steel and qualified for food grade or pharmaceutical grade filling. Our different models can fill from 3-5000 ml each fill.

All items are sold as is without warranty unless specifically stated in the posting. This does not mean that the unit doesn’t work, only that we have not tested or checked it out. This may also mean that we are not knowledgeable in this specific item.

(one) chemical slurry mixing blending pump transfer skid, includes slant bottom intake hopper, 30" x 28" x 36" deep with 12" opening at top, Effector high and low limit proximity sensors, hopper bottom electric vibrator, 9’ long x 4" diameter auger screw feeder that dumps into a 16" x 18" x 50" high pre-mix tank compartment with Mamec Oy mixer agitator, model HDS 5.5/1000, 6.5 KW, 1150 rpm, 440/480 vac, direct drive with dual stagger tooth impellers.

Despatch PND2-29-21E Inert Atmosphere Oven/Chamber Comes with a copy of the manual and what you see in the pictures. If you don't see it, you probably wont get it. Specifications are from Despatch and may vary slightly due to upgrades, options or revisions this unit may or may not have.

Veeco FPP-100 Four Point Probe Comes with a manual and what you see in the pictures. If you don't see it, you probably wont get it. Specifications are from Veeco and may vary slightly due to upgrades, options, or revisions this unit may or may not have.

Click Here. Double your traffic. Get Vendio Gallery - Now FREE!

NEW Comdel CDX-1000 Dual Frequency RF Generator/Power Supply Comes with what you see in the pictures. If you don't see it, you probably wont get it. Specifications are from Comdel and may vary slightly due to upgrades, options, or revisions this unit may or may not have.

Serial # LE198272 Input: 200/230 volts, 31/27 amps, single-phase - SET FOR 230VOutput: 160 amps at 24.5 volts DC, 60% duty cycleAmp range: 30-210 DC, 34.5 max OCVWire feed speed range: 35-700 inches per minuteWeight and Dimensions: 200 pounds, 19 x 39 x 32 inches

ER70S-6 is a mild steel welding wire that contains higher levels of manganese and silicon than other standard grades of MIG wire to produce high quality welds when used on dirty, oily, or rusty steel. The high silicon content increases the fluidity of the weld pool, thus creating a smoother bead appearance and resulting in minimal post-weld grinding.

Up for sale is a Hypertherm Powermax 1100 Plasma Cutter. Unit is equipped with the optional CNC interface and includes the machine torch shown in the pictures above. Unit worked when removed from service 2 weeks ago and has since been cleaned, inspected and powered on at our facility.

SquareTrade © AP6.0

When we introduced our first 200 amp AC/DC inverter machine 10 years ago, we were up against some major competitors. However, the market readily accepted the tough line of HTP Invertig welders. Fast forward to today – HTP introduces our third generation of AC/DC inverter machines, the HTP Invertig 221!

For your consideration

Here's the description: HYPERTHERM POWERMAX 65 W/25FT LEAD COMES COMPLETE AND IN ORIIGINAL BOX  Includes: Power Supply  25 ft. H65 Hand Torch  25 ft.