4 inch hydraulic cylinder for sale, brand-new and used.

New Page 3 Enerpac RC-104 Single Acting Hydraulic Cylinder with 4.13 Inch Stroke Attention Buyer : F

This is a new ENERGY HYDRAULICS tie rod, double acting hydraulic cylinder. The cylinder has a 4 inch bore diameter and a 24 inch stroke. It features a max pressure of 3,265 psi.

1 INCH PISTON DIAMETER, 1 INCH PISTON STROKE, 5 TON LOAD CAPACITY, PORTABLE HYDRAULIC CYLINDER This is a sweet nearly new 5 ton Enerpac 5 ton Hydraulic cylinder. Specs Piston Diameter 1" Piston Stroke 1" Load Capacity 5 Tons Outside Diameter 1-1/2" Lowered Height 4-11/32" Comes as shown. Ships at 2 lb ----------------------------------------------------------------------------------------------------

For sale is one Enerpac RC-210 50 Ton hydraulic cylinder with max working pressure of 10,000 psi. It has a 3.5 inch diameter cylinder with a stoke of 5 3/4 inches (** measured stroke is ~5 3/4 inch however makings on cylinder wall indicate up to 6") The cylinder is missing the hardened saddle that sits on top of the cylinder and the paint has seen some wear and tear however the sides of the piston are rust and damage free as is the base.

Prince Manufacturing Prince B350100ABAAA07B Double-Acting Tie-Rod Hydraulic Cylinder, Clevis Mounting, Painted, 3-1/2" Bore, 10" Stroke, 1-3/8" Rod Diameter, 3/4"-16 Thread, #8 SAE Port

Enerpac CLSG-2006 High Tonnage Hydraulic Lifting Cylinder, 200 (206.1) Ton (Max) Capacity, 5.91 Inch Stroke, 12.44 Inch Collapsed Height Description Hydraulic Cylinders, Jacks, Lifting Products and Systems Enerpac provides the largest selection of cylinders and lifting systems, fully supported and available through the most extensive network of distributors worldwide. We have a solution for virtually any application – lifti

[ Maxim 218-362 4 In Bore Dia 12 In Stroke Hydrualic Cylinder

[ Maxim 218-319 2-1/2 In Bore Dia 10 In Stroke 2500 PSI Hydraulic Cylinder

Enerpac SCR-102H Single Acting Cylinder Pump Set RC-102 Cylinder with P-392 Hand Pump

Enerpac SCL-101H Single Acting Cylinder Pump Set RCS-101 Cylinder with P-392 Hand Pump

This is a small hydraulic cylinder. I am not sure what is was made to do. It has one inlet and appears to be made to be welded in place by the angle bracket.

[ Maxim 218-367 4 In Bore Dia 20 In Stroke 2500 Max PSI Hydraulic Cylinder

[ Maxim 288-362 3-1/2 In Bore Dia 48 In Stroke 3000 PSI Hydraulic Cylinder

This Hydraulic Cylinder Jack has been on the shelf in an outbuilding for many years and I don't know if it's new or re manufactured, It has a 1/4" pipe NPT hole in both ends, still the original plugs in them, It's made by Ortman Miller Mach Co. Inc. Hammond Ind.

NEW CHIEF HYDRAULIC CYLINDER. PART NUMBER 207-428 IT IS;3 INCH BORE4 INCH STROKE1-1/2 ROD12 INCH RETRACTED16 INCH EXTENDEDSAE8 PORT SIZE1 INCH PIN HOLES3.500 OUTSIDE DIAMETER0.187 THICK WALLS

ENERPAC P39 P 39 HYDRAULIC HAND PUMP, 10000PSI

ENERPAC PH-39 PORTABLE HYDRAULIC HAND PUMP, 10000PSI