break lathe for sale, brand-new and used.

This is a Vintage Heavy High Quality pair of #2 Morse Taper drill bits as pictured from a Vintage 12" Sears Craftsman Metal Lathe #101.07403 with a 2 3/4" gap between bed rails. Have wear and tear dust and dirt some nicks rust and pitting but in good working condition. These could be used for a wood lathe also.

Sherline Lathe Accessory from LatheCity Connects a standard Jacobs drill chuck to Sherline tailstock 1/2”-20 to Morse Taper #0

This is a nice strong running used Dayton AC Motor marked Belt Drive Fan and Blower motor--actually was used on a wood lathe. It is model 5K258B...1/2 Horsepower 1725 RPM 60 HZ single phase 115 Volt 7.0 amp. Counter Clockwise (Left handed) rotation at shaft end Reversible Wear and tear rust dust and dirt but in good working good condition.

This is a really Super Heavy nice Live Center from a Vintage Large metal lathe. About 8 3/4" Long Tapers from about 1.05" to 1.25" at base of center has a somewhat dull point. Wear and tear rust and dust and dirt but in very good working condition.

This is an Indexable Tip Toolholder from a supply of 1000's of parts from a Vintage Large metal lathe kept in storage from a Metal shop that closed years ago This is a High Quality HEAVY tool--weighs over 3 pounds. Measures about 7" Long 1 1/4" X 1 1/4" The cutting end is @ 1 5/8" Tall and 1 1/2" wide. Most of these tools are considered New Old Stock NOS.Unused but not manufactured recently Minor surface rust and dust and dirt but in very good working condition.

This is an Indexable Tip Toolholder from a supply of 1000's of parts from a Vintage Large metal lathe kept in storage from a Metal shop that closed years ago This is a High Quality HEAVY tool--weighs over 4 1/2 pounds. Measures about 7" Long 1 1/2" X 1 1/2" The cutting end is @ 1 3/4" Tall and 2" wide. Most of these tools are considered New Old Stock NOS.Unused but not manufactured recently Minor surface rust and dust and dirt but in very good working condition.

Logan 10" Lathe Compound Slide Model 800 200 210 820 825 Montgomery Wards! Nice original compound assembly off a 10" Logan Lathe. Will fit Montgomery Wards 10" lathes too.

This is a boxed set of high quality Carbide tipped cutting tools from a supply of 1000's of parts from a Vintage Large metal lathe kept in storage from a Metal shop that closed years ago This is a full box of 10 about 2 1/2" Long Red colored Marked D6 Grade C5 Measure 3/8" Square. Made in Yugoslavia they say These are considered New Old Stock NOS.Unused but not manufactured recently Lots of surface rust and dust and dirt but in very good working condition.

This is a boxed set of high quality Carbide tipped cutting tools from a supply of 1000's of parts from a Vintage Large metal lathe kept in storage from a Metal shop that closed years ago This is a full box of 10 about 2 1/2" Long Silver colored Marked D6 Grade C2 Measure 3/8" Square. Made in Yugoslavia they say These are considered New Old Stock NOS.Unused but not manufactured recently Lots of surface rust and dust and dirt but in very good working condition.

This is a group of 12 Carbide tipped cutting tools from a supply of 1000's of parts from a Vintage Large metal lathe kept in storage from a Metal shop that closed years ago This is 12 2 1/2" Long Various colored 3/8" Square 2 1/2" Long. These are considered New Old Stock NOS.Unused but not manufactured recently Lots of surface rust and dust and dirt but in very good working condition. Still have ends sealed with a protective covering.

This is a group of 10 Carbide tipped cutting tools from a supply of 1000's of parts from a Vintage Large metal lathe kept in storage from a Metal shop that closed years ago This is 10 3" Long Copper colored Marked AR-7 Grade 78 Measure 7/16" Square 3" Long. Made in Detroit Michigan by Metallurgical division of General Electric. These are considered New Old Stock NOS.Unused but not manufactured recently Lots of surface rust and dust and dirt but in very good working condition.

This auction is for 5 Vintage Carbide tipped cutting tools from a supply of 1000's of parts from a Vintage Large metal lathe kept in storage from a Metal shop that closed years ago This is a set of 5 heavy copper colored cutters 3/4" X 1" and about 6" Long Made in Detroit Michigan by Metallurgical division of General Electric. These are considered New Old Stock NOS.Unused but not manufactured recently Lots of surface rust and dust and dirt but in very good working condition.

This auction is for 4 Vintage Carbide tipped cutting tools from a supply of 1000's of parts from a Vintage Large metal lathe kept in storage from a Metal shop that closed years ago This is a set of 4 heavy copper colored cutters 1" squared and about 6 7/8" Long Made in Detroit Michigan by Metallurgical division of General Electric. These are considered New Old Stock NOS.Unused but not manufactured recently Lots of surface rust and dust and dirt but in very good working condition.

This is a really Super Heavy nice Live Center from a Vintage Large metal lathe.Made by Motor Tool in Detroit Michigan USA About 13 3/4" Long It has an non tapered shaft about 9 1/4" Long 2" diameter. The center head is about 2 3/4" diameter has a slightly dull point. Turns quite freely.

This is a strong running HEAVY Vintage Emerson Electric 1/3 Horse Power from a wood lathe 1/3 Horsepower Model 115 Volt 60 Hz 1725 RPM 1 phase. Thermally protected. The shaft is 1/2" diameter round with a hole toward the end and about 1 5/8" Long Rotates counter clockwise at shaft end.

This is a strong running 1/3 Horsepower AC electric motor from a RTC wood lathe #GL-1000 Made by Taiwan Shopmaster Co. LTD. Dust and dirt wear and tear rust and pitting but in good working condition.1/3 Horse 1720 RPM 115 Volt 60 Cycle 7.5 amp made in 1988 cord has been spliced.

This is a really heavy cast iron motor mounting plate about 11" X 11" From a vintage 10" Delta Rockwell 10" Wood Lathe Serial # D1868 with a 1 1/4" Gap between bed rails. Some wear and tear dust and rust pitting and dirt but good working condition.tightens to work table with adjustable "pins" on 1 end. the other end tightens or loosens the bracket to release belt tension.