dc calibrator for sale, brand-new and used.

Fluke 715 Volt/mA calibratorBarely used, as new condition.Fully tested. Bid with confidence! Functional Specifications

20MHz Dual Trace Oscilloscope with Alt-Mag 20MHz Bandwidth Alt-Mag sweep for simultaneous display of main and X5 magnified trace 1mV/Div Vertical sensitivity Alternate trigger for a stable display of unrelated signals X5 Sweep Magnification Large 6 inch CRT with internal graticule, for parallax free measurements Autofocus Internal Sync spearator circuit for stable triggering on video signals Leightweight with low power consumption Supplied with 2 (X1, X10) probes and operating manual

Rosenberger 53S35R-MSOB1 Short Open Load Calibration Adapter DC-5GHz Precision 50 ohm, Male N connectors, Short, Open, Load reference. Rosenberger part number 53S35R-MSOB1. Silver plated contacts.

Up for grabs is a really nice Altek TechChek 820 Multifunction Calibrator. I checked this one out a month ago and it's fully functional and in very good shape. There is a slight chip out of one of the corners, but this is hard to notice and doesn't affect the operation in any way.

The Altek Model 334 will check, calibrate and measure all your current signal instruments in a 4 to 20 milliamp DC loop. Use at every point in your loop. Source & Read 0.00 to 24.00 mA, Simulate a 2-wire transmitter or use the Model 334A to simultaneously power & measure your 2-wire transmitters.

SOURCE and READ T/C’s over the entire industrial temperature range with ALTEK’s Model 322 Thermocouple Calibrator. Use with transmitters, recorders, controllers, alarms, indicators,data acquisition and computer systems. Switch between fourT/C types or millivolts.

Up for sale I have a Fluke 5500A/EP Switch Accessory for use with the 5500A multifunction calibrator during MetCAL automated calibrations of the Fluke 8840A and 8842A, HP/Agilent 34401A and 3478A and the Keithley 2000 multimeters. It essentially, in conjunction with a 3458A and Fluke MetCAL software, allows you to perform calibrations of the precision multimeters listed without changing connections at all during the calibration procedure.

Serial Number: 7140205. Photo is stock photo. This unit is used with average usage, and includes the SC600 600 MHz oscilloscope calibration option.

Fluke 51 II Digital Handheld Thermometer You are buying a Fluke 51 II Digital Handheld Thermometer. Unit is used with marks from use, please see photos. Only the meter and yellow holster are included.

Time Electronics 609N 49-1468 L2-E DC Current Calibrator 200/240VAC 1A Item Condition: Used Quantity: 1 Unit Cosmetic Condition: 8 Functionality: power on test ok - Remarks: Actual Weight: 3.2Kg Dimension: 22x16x21 ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Comes with 14 days money back guarantee.

BEST OFFERS WELCOME Up for sale is a used Valhalla Scientific 2701C Programmable DC Voltage Standard from surplus. The unit has some scrapes and dings from previous use (SEE PHOTOS as photo description supersedes text description), but is otherwise clean and in good physical condition. Please check out our other testing equipment auctions.

Raspberry Pi, Arduino, PIC Geiger Counter Calibration Micro Controller If you are designing / developing a geiger counter with one of these micro controller platforms the calibration microcontroller allows you to test your design to insure that it's counting accurately Features: Based on a Microchip 12F683 8 bit controller Low parts count - see attached schematic - Microcontroller and battery or other DC supply - that's it. Can output a 3 Volt or 5 Vol

You are bidding on a good used Fluke 5440B/AF Direct Volts Calibrator Checked and in good working order Has a slightly dim display and a few scuffs here and there but otherwsie is a nice unit The Fluke 5440B Direct Voltage Calibrator is equipped with bright vacuum-fluorescent displays for clear visibility at any viewing angle. The 5440B offers output voltage of 0 to 1100 VDC with accuracy of 3 ppm. Completely automatic internal calibration, no mechanical adjustments.

24 V Loop power supply HART mode setting with loop power (adds 250 ohm resistor) 100 % larger dual display 1,200 ohm drive capability on mA source Enhanced backlight with two brightness settings 0-100 % mA Span Check buttons to toggle between 4 and 20 mA Infrared I/O serial port compatible with FlukeView® Forms Software Version 2.1 (available Feb.

VINTAGE HEATH KIT VISUAL AURAL TRACER, LC6-388COLOR BAR PATTERN GENERATOR & DC-AC PRECISION CALIBRATOR MODEL 421 MADE BY BALLANTINE LABORATORIES - TALLEST IS 13"00012007628

The DMMCheck Plus is a battery powered device that checks seven important functions on a DMM: AC and DC Voltage, AC and DC current, Resistance, Frequency, and Duty Cycle. It you have a DVM or DMM that has questionable accuracy, the DMMCheck Plus can give you the confidence you need before relying on your test equipment. Provided on the small (3"W x 3"L) circuit board are the following circuits: Resistance : Four 0.1%, 10ppm/C precision resistors are included: 100?, 1.00K?, 10.00K?, and 100.0K?

Sper Scientific Sound Level Meter with Graphic Display - 5 Year Warranty Like Sound Meter 840029 model, 840028 also covers 30-130dB in the A scale and 35-130dB in the C scale with a resolution of 0.1dB and an accuracy of +/-1.5dB. Model 840028 also meets ANSI S 1.4 type 2 and IEC 651 type 2, and includes A & C decibel frequency weighting s

Fluke 117 True RMS Digital Handheld Multimeter You are buying a Fluke 117 True RMS Digital Handheld Multimeter. Unit is used(???) and like new condition, please see photos. Comes with a Fluke TL75 Test Lead Set, Fluke 2538674 Rev 1 2/07 Users Manual, compliance, calibration practices, and registration paperwork.

.shippingcalculator a { display:block; width: 208px; padding:177px 0px 10px 0p