fixture clamp for sale, brand-new and used.

Professional TDS-100H-M1 Ultrasonic Flow Meter Flowmeter Clamp on Sensor   Fast shpping DHL / EMS / Fedex New user manual

Professional TDS-100H-M2+S1 Ultrasonic Flow Meter Flowmeter Clamp on Sensor Fast shpping DHL / EMS / Fedex Product Features: 1.This listing is for DN15-700mm pipe size, the water temperature is from -40-90 degree 2.it comes with S1 transdcuer (DN15-100mm) and NEW M2 transducer (DN50-700mm); 5m*2 signal cable;metal

Vintage and used but in excellent condition. All edges and corners are sharp and undented. There is 3/4" capacity for round stock with the clamp screwed in place.

Pipe, Rod or shaft holder: 5" max od Fixture work holder for round part machining or welding or other processing.Very rigid steel set-up w/toe clamp holding arms. 1/2" CR steel fixture w/black oxidefinish, 11"x7" x appro 7" high Mounting pattern for the plate is 4"x4" using 1/2 cap screws or bolts.Happy Bidding!

ETM Rotary Tool Clamp System - COUNTERBORE DIAMETER: 3-7/32" DEPTH OF V FLANGE: 2-23/64" Taper: 40 40 TAPER ROTARY TOOL CLAMP SYSTEM - ETM

Universal key cutting machine for door and car key Cutting Machine Locksmith Equipment

Universal key cutting machine for door and car key Cutting Machine Locksmith Equipment

Wire EDM Large Part Fixture All parts are made with 420 stainless steel and hardened to 45-55 RC (unless specified) precision ground +/-.0002" flat/parallel. 1- Fixture 2- Sloted clamp 5mm SHCS(stainless) for mounting clamps, and a stop 5mm set screws(stainless) for holding part Hieght is 2 inch, width is 2 inch, lenght is 6 inch part step is 1.25 inch X 1.25 inch (size may vary) The two screw counter bores are for 8mm x1.25 screws and they are 50mm apart.

Wire EDM Small Part Fixture Cost: $200 All parts are made with 420 stainless steel and hardened to 45-55 RC (unless specified) precision ground +/-.0002" flat/parallel. 1- Fixture 1- Sloted clamp 1- side clamp 4- 5mm SHCS(stainless) for mounting clamps, and a stop 3- 5mm SHCH(stainless) for holding part Hieght is 1 inch, width is 1.25 inch, lenght is 6 inch part step is .5 inch X .8 inch (size may vary) The two screw counter bores are for 8mm x1.25 screws and they are 50mm apart.

This is a very nice older unit that I went through & fixed up I replaced the bearings Added 2 stops Anodized the handle & dial Reground the v-block & added the clamp it will now indicate with in .0002 I am also including a taped fixture plate I have used this unit & it works as good as a new one witch will cost $2349.99 + TAX & shipping Any questions call Fred Creath at 847-888-2420

This fixture was used to sharpen the larger diameter “E” see link at bottom Its best suited for a surface grinder or on a tool and cutter grinder with a magnetic chuck. With some ingenuity I suppose you can adapt this for other styles but it’s made for the

Union Butterfield Grinding Fixture List No. 140 Catalog Number 69-30001 Universal Grinding Fixture with 3 Graduated Angle Adjustments and gage with clamp. This is a "spade drill insert" grinding fixture good for sizes above approximately 2" wide (diameter).

"Being able to custom configure yo

Four Skanda 9820 halogen light fixtures with clips for illuminating trade show booths, exhibits, and displays. Like new condition. Sold in pairs only - $100 pair or $200 for all four.

????? 998C Universal key cutting machine For door and car key Locksmith Equipment 110V

HARIG DUO-FORM AND UNIDEX GRINDING FIXTURE WITH WOOD CONSTRUCTION STORAGE BOX NOS. 3094821 3.00" CENTER HEIGHT IT HAS 2 LOCK DOWN SCREWS FOR THE V-BLOCK CLAMP 1 INCH LONG AND 2 INCHES LONG THIS FIXTURE IS IN VERY GOOD CONDITION AND LOOKS TO HAVE NOT BEEN USED VERY MUCH UNKNOWN AGE THIS FIXTURE HAS LIGHT USE AND THE INDEX IS A LITTLE STICKEY FROM NOT BEING USED AS PER EBAY RULES THE SALE OF THIS IT

Skanda 9210 Light Fixture

Skanda 8822 Light Fixture