ground block for sale, brand-new and used.

National Instruments SCXI-1327 High-Voltage Attenuator Terminal Block Comes with what you see in the pictures. If you don't see it, you probably wont get it. Specifications are from National Instruments and may vary slightly due to upgrades, options, or revisions this unit may or may not have.

This auction is for a partial box of 80 Wago Fused Disconnect Terminal Blocks with Blown Fuse Indication, part number 281-622/281-541. They are Gray and rated for 28-12 AWG wire. This information is from the Wago website: Fused Disconnect Terminal B

This auction is for a partial box of 45 Wago 3 Conductor Double-Deck Terminal Blocks, part number 870-539. They are Blue and rated for 28-14 AWG wire. Information from the Wago website: 3-conductor, double-deck terminal block; 6-conductor through terminal block; N; b

For sale is a *box of 50* of Telemecanique part number AB1AAET235UGR. DOUBLE DECK GRAY TERMINAL BLOCK, 10A, 600V, #16-14AWG These are considered new and will come in the original manufacture carton, no user manual or installation guide included. Unit carton may show signs of shelf life.

13 lots of DIN mount terminal blocks. All new and never used. Each line below is 1 lot.

For sale are (3) of an ABB part number FJ304-3PB6BN. (Can be purchased separately) ENCLOSED 30A FUSED DISCONNECT, CLASS J, NEMA 4, WITH NEUTRAL BLOCK Units are considered new and will come in the original manufacture carton, along with a specification sheet in each unit. One of the units has the "N" hand written on the unit carton and on the inside of the enclosure, but does include the neutral block.

GOULD SHAWMUT 164033J 600V 200 AMP Class J - BLOCK LUG TERMINAL 3 POLECU-AL 200 use 75 deg.C WireUser Class J FusesTorque 275 in LBS.HCR-I *102426

I have a very nice used National Instruments SCB-100 182788C-01 shielding I/O connector block for sale. Cosmetically I would rate it a 9 out of 10. I picked this up in a plant closure along with some other items and I'm passing the savings to my buyers.

This listing is for a used and tested, National Instruments (NI) PCI-6232 16-bit isolated industrial DAQ board, with NI recommended SH37F-37M-1 interface cable, 1-meter length (new in bag), and used NI CB-37F-HVD screw terminal block. The PCI-6232 and terminal block are used and in good working condition. The items are same as shown in the photos.

Wire EDM Vise And Mount Block Vise All parts are made with 420 stainless steel and hardened to 45-55 RC Vise is precision ground +/-.0002" flat/parallel. Vise will open up to almost 3.5 inches Each vise comes with a removable setup rail!!! Mount Block Made with 420 stainless steel and hardened to 45-55 RC precision ground +/- .0002 flat/parallel comes with stainless socket head cap screws for bolting together Thanks Brad B.

Wire EDM V-Block And Mount Block All parts are made with 420 stainless steel and hardened to 45-55 RC V-block is precision ground +/-.0002" flat/parallel. Each V-block comes with a removable setup rail!!! V-block will hold up to 2.5 inch diameter or a 2.75 inch square piece.

Wire EDM V-Block 1.5 X 5 X 5 (inch) Will hold up to a 3 inch diameter. 420 stainless steel (hardened 48-52RC) With - clamp - set up rail - stainless socket head cap screws - side rail (for standing block up or on its side) - (3) clamp screws The slotted screws are for M8 and M6 socket head caps screws they are machined 50 mm apart so these will work in any Wire EDM machine. Main Block is precision ground +/- .0002" flat/parallel

table.transapptable { border-width: 5px; border-spacing: 2px; border-style: solid

table.transapptable { border-width: 5px; border-spacing: 2px; border-style: solid

table.transapptable { border-width: 5px; border-spacing: 2px; border-style: solid

table.transapptable { border-width: 5px; border-spacing: 2px; border-style: solid