long elbow pipe for sale, brand-new and used.

This listing is for a large group of 1-1/2 inch copper pipe and fittings. These are new old stock and are unused unless noted. They have never been used and are ready for the next job unless noted.

Jewel No. 5M Long turn made of malleable ductile For use on both mains and risers. Can be used on the bench, on the ground, or up on the lines.

Conduit Pipe3" EMT22 total piecesAll ElbowsNEWGalvanized Steel4 Each: 3" Elbow 30 Degrees (approx 19 1/2"long)7 Each: 3" Elbow 45 Degrees (approx 19"long)1 Each: 3" Elbow 30 Degrees (approx 21 1/2"long)

Warthog WV-P4 1/4" NPT 3-3.5GPM @ 3,000PSI to 4,000PSI Details The WV-P4™ is the newest member of the WARTHOG®family. It differs from our other WARTHOG

This sale is for a NEW OPW Engineered Sytems 90 degree elbow swing/swivel joint. It fits a 1 inch pipe size. NPT threaded female ends.

Armstrong SG-33 3" x 3" Cast Iron Suction Diffuser Pump 516860-019 Suction Guide Armstrong's Model SG suction guides are designed for direct mounting to the suction side of horizontal or vertical pumps. Guide vanes provide proper flow conditions by reducing water turbulence to minimize stress on pump parts. Space savings are achieved through elimination of long radius elbow, suction entrance pipe, and conventional 'Y' strainer.

HPS MKS BOULDER CO VACUUM PIPE CHAMBER ELBOW VALVE Descriptions Used unit, good condition, auction from the company closed out, item sell as is. Please look over in the 7 photos for more detail. HPS MKS BOULDER CO VACUUM PIPE CHAMBER ELBOW VALVE / CAL-MELD 05-3629/A (Stainless Steel) long 19 inch and 13"1/2 inch, face 3" 3/4 inch with 1 UE PRECISION SENSOR DIV 20 TORR SWITCH and 1 UE PRECISION SENSOR DIV ATMOSPHERIC SWITCH Local pick up free Used Unit.

!!! PACK OF TEN (10) BRAND NEW 2.5 LITRE AUTOMATIC DRINKERS !!! JUST ?23.99 EACH DELIVERED with FREE SHIPPING nothing more to pay Get plumbing and provide a continuous supply of fresh water to your pigs, sheep, goats, chickens, ducks, dogs.

Selection of 48mm & 42mm KEE Clamp Handrail/Pipe System Galvanized Steel. 10 x 48mm 90Elbows, 64 x 48mm Base platess, 6 x 48mm 90 elbow Swivel, 8 x 48mmLong Tee 6 x 48mm 90 Corners, 13 x 48mm Inline External. 4 x 42mm 90Elbows, 6 x 42mm 90 elbow Swivel, 9 x 42mm Long Tee 4 x 42mm 90 Corners.

This is a rather hard to find original fuel mixer or carburetor for a Fairbanks Morse Z gas engine. It is in good original condition with no cracks, breaks, or repairs of any kind except that it needs a new fuel jet that delivers gas to the head. This is nothing more than a small piece of copper tube in place where my finger is pointing in one of the pictures.

SAUERMANN DP1102SIUS11 THIS KIT ONLY INLCUDES THE CONDENSATE PUMP, FLOAT AND THE DUCT. The kit includes a SI1102 one-piece condensate lift pump complete with float detector. This kit is specifically designed for quick installation of the pump inside an elbow.

Lot of 3 8" Schedule 40 Elbow Long Sweep Electrical Conduit Plumbing Pipe Belled

THIS MOTOR WAS TAKEN OFF A MACHINE NO LONGER IN SERVICE AND IS IN ECELLENT CONDITION. WHILE ON THE MACHINE WE NEVER DID USE ITS FUNCTION SO THE MOTOR HAS NEVER BEEN RAN WHILE INSTALLED. Leeson Motors Gearmotor-Right-Angle Shaft, 29RPM, 1/6HP, TEFC, 115/230V, AC Product Specifications HORSEPOWER1/6 RPM29 TORQUE IN LBS110 FRAME38 TYPE-FRAME13F60-38F ENCLOSURETEFC AMP2 PHASE1 VOLTAGE115 / 230 OVERHUNG LOAD LBS.235 SHAFT ORIENTATION