LOTOS CT520D 50A Plasma Cutter 200A Tig Welder, Stick Welder, US $1500 – Picture 0

LOTOS CT520D 50A Plasma Cutter 200A Tig Welder, Stick Welder, US $1500 – Picture 1

LOTOS CT520D 50A Plasma Cutter 200A Tig Welder, Stick Welder, US $1500 – Picture 2

LOTOS CT520D 50A Plasma Cutter 200A Tig Welder, Stick Welder, US $1500 – Picture 3

LOTOS CT520D 50A Plasma Cutter 200A Tig Welder, Stick Welder, US $1500 – Picture 4

LOTOS CT520D 50A Plasma Cutter 200A Tig Welder, Stick Welder, US $1500 – Picture 5

LOTOS CT520D 50A Plasma Cutter 200A Tig Welder, Stick Welder, US $1500 – Picture 6

LOTOS CT520D 50A Plasma Cutter 200A Tig Welder, Stick Welder, US $1500 – Picture 7

LOTOS CT520D 50A Plasma Cutter 200A Tig Welder, Stick Welder, US $1500 – Picture 8

Lotos Ct520d 50a Plasma Cutter 200a Tig Welder, Stick Welder

US $1500

Sunnyvale, California, United States
Jan 30th

Open on mobile:
QR code

Lotos CT520D Manual General Overview The LOTOS CT520D multipurpose units offer a variety of multiple welding and cutting aspects. It is able to cut all types of metal up to 1/2’’ with the 50A plasma cutting function. The hand carrying weight is 32 lbs, the unit is portable and reliable featuring a duty cycle of 60% at max amps on all processes. Specifications General Model Name CT520D Functions 50 A Plasma Cutter200 A TIG Welder200 A STICK Welder Dimension with handle L x W x H 17’’x 8’’x 14’’ Weight 32 lbs (14.5 kg) Input Voltage 110-220 V, 1-PH, 50/60 Hz Power supply type Inverter - IGBT Housing Protection IP21 Insulation B Efficiency 85% Accessories Plasma cutting torch 50 A, 12.5 ft. (3.81m) TIG welding torch 200 A 12.9 ft. (3.93m) Arc/Stick clamp 200 A 6.5 ft. (1.98m) Argon regulator 0-250 psi Air Regulator 0-150 psi Plasma Cutting Rated input power requirement 120-220 V, 1-PH, 27 A+/- 15%, 50/60 Hz Output current 10-50 A @220V10-25 A @110V Duty cycle @ 40°C (104°F) 60% @ 50 A100% @ 40 A Gas supply Clean, dry, oil-free air Recommended gas inletflow rate / pressure 3.6 scfm @ 65 psi80L/min Max Rated Cutting Thickness 1/2 inches (12.7mm) DC TIG Welding Rated input power requirement 120-220 V, 1-PH, 17 A+/- 15%, 50/60 Hz Output current 10-200 A @ 220V10-100 A @ 110V Material can weld Steel, Stainless, Moly, Ferrous Duty cycle @ 40°C (104°F) 60% @ 200 A100% @ 150 A No load voltage 62 V Working Voltage 16.9 V Gas supply Clean, dry, oil-free argon gas Starting Mechanism High Frequency Start / HF Welding Recommended gas inletflow rate 2-5 L/M DC Stick Welding Rated input power requirement 120-220 V, 1-PH, 23 A,+/- 15%, 50/60 Hz Output current 10-200 A @ 220V10-80 A @ 110V Material can welding Steel, Stainless, Moly, Ferrous Duty cycle @ 40°C (104°F) 60% @ 200 A100% @ 95 A No load voltage 62 V Working Voltage 25 V Starting Mechanism High Frequency Start / HF Welding CONTROL PANEL Applicable Torch Type Torch Type Model Amperage Consumables Type 5 prong LCON cutting torch CL0105 50 LCON0120 LCON0140 LCON0190 Extended 5 prong LCON cutting torch CL0205 50 LCON0220 LCON0240 LCON0290 Applicable Consumables Package Part Number Nozzle Electrode Shield Cup Swirl ring Package Type Total Pieces LCON0120 LN01 LE01 LC01 LR01 LN01 x 10,LE01 x 10 20 LCON0140 LN01 LE01 LC01 LR01 LN01 x 10, LE01 x 10, LR01 x 10, LC01 x 10 40 LCON0190 LN01 LE01 LC01 LR01 LN01 x 40,LE01 x 20,LR01 x 20,LC01 x 10 90 LCON0220 LN02 LE02 LC02 LR02 LN02 x 10,LE02 x 10 20 LCON0240 LN02 LE02 LC02 LR02 LN02 x 10,LE02 x 10,LR02 x 10,LC02 x 10 40 LCON0290 LN02 LE02 LC02 LR02 LN02 x 40,LE02 x 20,LR02 x 20,LC02 x 10 90 Accessories (Click to view FULL size image) Unrivaled Quality The production process for Lotos products is among the most stringent in the world and meets or exceeds some of the industry's most rigid standards. Our studies show that it is in fact among one of the best in the industry and is unrivaled by other would-be competitors. The quality of each of the integrated components is constantly monitored during the course of production. Only components and materials that meet the highest industry standards for quality are permitted to be incorporated into our LOTOS line of products. Finally, upon conclusion of production, each unit is put through a newly devised, far more rigorous 30 point testing and quality inspection routine. This process is critical to ensuring a product that is not only safe, but reliable in both performance and durability. Cut at 12 Times the Speed of Sound Plasma cutting is a process that is used to cut steel and other metals using a plasma torch. In this process, an inert gas (compressed air) is blown at high speed out of a nozzle; at the same time an electrical arc is formed through that gas from the nozzle to the surface that is being cut, turning some of that gas to plasma. The plasma is sufficiently hot to melt the metal being cut and moves sufficiently fast to blow molten metal away from the cut. The plasma, which is maintained between the work-piece and electrode, travels at over 9000 MILES PER HOUR (15,000 km/Handle). That’s over twelve times the speed of sound. Advantage of Plasma vs. Oxy-Fuel Torch Plasma does not use expensive, hazardous gases, only compressed air. It imparts much less heat into the piece being cut, eliminating warping. It does not require ignition. It leaves little to no slag to clean up or grind off. The cost per cutting hour can be less than oxy-fuel since there is no gas cost. It is also much quicker and easier. So, you cut better, faster and inexpensively. Skill and Training There is not a lot of skill or training required to operate a plasma cutter. The torch should remain at a 90-degree angle. ADVANCED INVERTER TECHNOLOGY The CT520D inverter rectifies the input voltage (110V or 220V) into DC (Direct Current), which is then fed into a series of MOSFETs (Metal Oxide Semiconductor Field Effect Transistor). LOTOS LT5000D/CUT50D utilizes the most advanced TOSHIBA MOSFETs. These MOSFETs (transistors) are switched at thousands of Hertz, which greatly reduces the magnetic flux, and therefore the size of the transformer. Hence, the use of MOSFETs allows for a compact and light weight machine such as the CT520D to operate at its performance parameters. In simple terms the use of these MOSFETs makes it possible for CT520D to produce the necessary power, using very little space and creating minimal heat dissipation. Payment We accept Paypal, Credit cards (Visa/Master/Discover/American Express), Money Order or Checks. Please contact us if you have any questions. International customers, please contact us for shipping fees. Shipping and Tracking FREE FedEx shipping with FREE tracking information to 48 states. Additional Shipping Info: Priority mail (2 to 3 days) is $39 FREE tracking information Canada FedEx Ground: $39 Canada Priority Mail Shipping: $79 International Priority mail (to European countries and Mexico, Brazil): $120 International Priority mail (to Australia): $160 We try our best to ship the item within 2 business days after payment is received (most of time within 1 business day) FedEx does not ship to a PO Box address, you have to use priority mail to ship large packaging to a PO box address WARRANTY, SERVICE and PARTS Warranty Terms: Lotos Technology warrants that all equipment sold by our company, unless otherwise specifically stated, will be free from defects in materials and workmanship for a period of 1 year from date of shipment. Such warranty shall not apply in any event to failure or defects in materials due to normal wear and tear, failure to perform recommended or customary maintenance procedures, exposure to detrimental elements, improper storage, or corrosion, and shall not extend to any person or entity other than the customer. To purchase an extra 3 years' warranty, please click here. Return: After shipment, product is returnable for a refund within 30 days of shipment, with a minimum 20% restocking fee. Lotos Technology reserves the right to charge a restocking fee higher than 20% based on the condition of products received. Original shipping and handling fee is not refundable. Feel free to contact us if you have any questions or comments. Useful Information for Lotos (BL)CT520D: Here is the video link for machine setup and operation. http://www.youtube.com/watch?v=5TM3_gtOQLE a better user manual is online now, check following link (and thanks to Anthony, our Canadian dealer) http://www.lotoswelders.ca/manuals/CT520D_opt2.pdf For Plasma Cutting For your convenience, the initial consumables are included in the package. However, you may need extra consumables/parts for your project. We provide the following three packages for our customers- LCON40 LCON90 LCON150

Condition:	New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. ...	Brand	LOTOS
Power Source	110/120V Electric, 208/240V Electric
Model	CT520D
Processes	Plasma, Stick, TIG
Country/Region of Manufacture	China
Current	1 Phrase
Multi-Process	Yes