machine jack for sale, brand-new and used.

CONCRETE PUMP FOR SALE, CAN HANDLE UP TO 1/2 INCH AGGREGATE, PUMPS 25 CU. YDS/HR, DIRECT FLOW MANIFOLD, NEW HOPPER GRATE, NEW PIVOT JACK STAND, ONE PIECE CRANK SHAFT, LARGE BACK SPLASH, NEW SEATS, NEW BALLS, 1,109 HOURS, NEW WEAR PARTS, REMOTE CONTROL, NEW FENDERS, NEW PAINT AND DECALS, GREAT MACHINE, 100% REFURBISHED. Performance Pumping Rate 25 cu.

Imer Mortarman 360 Mortarman 360 This unit has been steadily finding its way into precast shops, concrete countertop makers, cultured stone fabricating shops and masonry projects across the country. It is a bullet proof machine that just keeps on producing. The Mortarman 360 is just over 3 years old as of 2006 which has led to a new manufacturing facility in Italy just to handle the increased sales and optimism in vertical shaft mixing.

Good replacement ram, springs, handle and spring bracket for the popular 16 ton hydraulic tubing benders. collapsed height is 14" and its 23-3/4" tall when extended.013-06-11-crm PLEASE READ BEFORE BIDDING: Contact me for correct freight rates as the calculator may be incorrect EB

Up for auction is a used Clarke-American B-2 Edger. This edger is in good used condition....the edger runs in both speeds but there seems to be more spark from where the brushes meet the armature than normal. It comes with a cord and bolt/washer.....no bag or case.

Up for auction is a very nice Clarke Floor Crafter Floor Sander. This is a very aggressive sander that gets the job done! The drum is excellent as is the rest of the machine.

Wacker Neuson BTS630 and BTS635 Cylinder & Piston Kit | A Genuine Wacker Neuson Part 5100005808 This cylinder and piston kit is a genuine OEM replacement assembly for the Wacker Neuson BTS630 and

Wacker Neuson BTS630 & BTS635 Air Filter Set | A Genuine Wacker Neuson Part 213483 This air filter set is a genuine OEM Wacker Neuson replacement part for the BTS630 and BTS635 concrete cut-off saw. This set includes the pre-filter and air filter, and is a

Wacker Neuson BTS630 & BTS635 Starter Recoil | A Genuine Wacker Neuson Part 213769 This starter recoil assembly is a genuine OEM replacement part for the Wacker Neuson BTS630 and BTS635 concrete c

Echoes from the Oil Country (American Machinist Memories), Volumes 1 through 5, originally published in American Machinist magazine in 1901-02. Republished by Lindsay Publications, Bradley, IL, 2005. Each book is 5 1/2 x 8 1/2 paperback.

Old Vintage Rare Monitor Baker Windmill Company Evansville, Wisconsin Hand Hit & Miss Engine Cast Iron Windmill / Hand Water Well Pump. Very nice old original Monitor Script pump. Matches the Monitor Baker pump jack engines, hard pump to find with Monitor Script name.

I am pretty sure this fits an upright 2 hp. It is bigger than my pump jack muffler Some of Charliebrowns rules! If you read this, we won't have so many troubles.

here are 4 wheels that would have been on a Factory 1 1/4 hp Monitor cart. I thought I might find a pattern for the mounts, but not so far. Some of Charliebrowns rules!

For sale brand new timing gear for the 11/4 HP upright Monitor antique stationary gas engine pump motor. This will replace the often wore out small gear. Gear is made like original and is keyed.

2 hp T fuel pump eccentric bronze castings. Requires machining. Some of Charliebrowns rules!

2 hp T detent arm casting. Requires machining. Some of Charliebrowns rules!

I think the pattern was on a Jack Junior 1 hp, but it is the same as on a 2 hp T. Requires machining. Some of Charliebrowns rules!

Monitor pump top, cross bar. I think this is the earlier one, as it just has a pin, rather than the sliding double pin. Some of Charliebrowns rules!

I think this fits from around 2-5 hp engines, not real sure, it is the only one I have, and I have not mounts. It is 12" by 3". It has one chip I see.

I do not recall what the pattern was from for sure,but it is the same as on a 2 hp T. I do not know if it fits anything else Requires machining. Some of Charliebrowns rules!