snap in nut for sale, brand-new and used.

var itemNumber = window.ebayItemID ?

var itemNumber = window.ebayItemID ?

Title of your page goes here 1941 MACHINE SHOP TOOLS LATHE MILL JIGS FIXTURES FOUNDRY GEAR CUTTING      This is a 568 page, 5 3/4” x 8 1/2”, hardcover book titled The New Encyclopedia of Machine Shop Practice.   The book was edited by George W. Barnwell Professor of Production Practice Stevens Institute of Technology and was copyrighted and published in 1941.

SNAP-ON TOOLS MODEL No. PWA10A, 10", STRAIGHT JAW, ALUMINUM HANDLE PIPE WRENCH SNAP-ON PWA10A PIPE WRENCH.STRAIGHT JAWS.ALUMINUM HANDLE.10" NOMINAL LENGTH.1-1/2" PIPE CAPACITY.NO INSTRUCTIONS OR PACKAGING.MADE IN U.S.A. PIPE WRENCH IN CLEAN, EXCELLENT, NEAR NEW CONDITION - GOOD JAWS, NUT & SPRING - A FEW MINOR FINISH SCRATCHES - NOT ETCHED - SOLD AS IS

- Thanks for looking! I'll be listing additional machinist, gunsmithing, milling, lathe, precision measurements gear/equipment, micrometers (id = inside diameter; od = outside diameter) in next few days - This item is in like-new condition - Buy Now payment due immediately. Paypal only.

SNAP-ON TOOLS MODEL No. PWA14A, 14", STRAIGHT JAW, ALUMINUM HANDLE PIPE WRENCH SNAP-ON PW

DESA Fuel filter M19630 Part #M19630 Fuel filter used on oil fired / kerosene heaters , was used on a lot of the older larger heaters 150k btu and up too. This part is compatible with the following machines: (this is just a partial list I gathered up quickly) M50, M50D, M50S, M65/D, M66D, M85/D, M100, M100D, DESA: Dayton, Knipco, Koehring, Master, Reddy, Reming

Up for sale is a USED Snap-On - 5/8" Flare Nut/Line Wrench, Part # - RXS20 -

Up for sale is a USED Snap-On - 1/2" Flare Nut/Line Wrench, Part # - RXS16 -

Up for sale is a USED Snap-On - 9/16" Flare Nut/Line Wrench, Part # - RXS18 -

Up for sale is a USED Snap-On - 7/16" Flare Nut/Line Wrench, Part # - RXS14 -

Up for sale is a USED Snap-On - 3/8" Flare Nut/Line Wrench, Part # - RXS12 -

Fastest and easiest way to remove brass compression rings from copper piping Removes brass compression ring in seconds No damage to copper pipe No mushrooming the end of co

Snap On Flank Drive Flange Nut Wrenches12 Point 1/2 inch Drive 2 Wrenches:One Wrench is 1-7/8 inchThe other is 2-5/16 inch They are used but not much. I have had these for thirty five years and have only used then a few times. They are in good condition.

This "BRAND NEW" UNOPENED BOX Kegco Standard Tower Conversion kit is the perfect solution for those who are converting a compact refrigerator or converting a freezer into a kegerator. This kit comes with brand new, high quality draft beer components and contains everything (except 5 lb. co2 tank) you will need to successfully convert your compact refrigerator/freezer into a kegerator at great savings.

This is a set of wrenches that is in great shape. They are great for breaking loose a nut or bolt that is hard to reach place or hard to come loose. Comes as pictured with organizer.

Make adjusting the degrees on your 4" band saw a snap. Simply turn the handle to loosen the fence, adjust the degrees and hand tighten. Handle, bolt, nut, washers (and secret component, not shown) included.

MANUFACTURER'S DESCRIPTIONAdaptors held on drivers with knurled nut. Small and medium drivers (A157-3 and A157-2) fit all smaller bushings (A157-6 thru A157-12); large driver (A157-1) fits remaining bushings (A157-13 thru A157-22). Set comes packaged in PB20 storage case.