Tools for Fabrication Equipment (Tools for Specific Machines) for sale, page 47

"v" blocks mini pair with #40 (.098) new !!

Haysville, Kansas, United States
Jun 9th

UP FOR SALE IS THIS PAIR OF MINI "V" BLOCKS FOR PRODUCTION USE. THIS IS A NEW PAIR STARTING WITH CARR-LANE BLOCKS THAT ARE CASE HARDENED. THEN DRILLED ON CENTER IS A PRESS FIT # 40 (.098) DIAMETER DRILL BUSHING.

Panavise arbor press

Tampa, Florida, United States
Jun 9th

Panavise Arbor Press - USED Missing presure gauge and handle. You can the press without it presure gauge but you need to replace the handle. Needs cleaning and lubrication.

Benchmaster 1ton obi punchpress with 34" stand pick up only bolingbrook il 60490

Bolingbrook, Illinois, United States
Jun 9th

Metal roller - unknown brand name - pick up only bolingbrook il 60490

Bolingbrook, Illinois, United States
Jun 9th

Peck stow & wilcox vintage bead roller crimper sheet metalworking antique tool

Woodbridge, Virginia, United States
Jun 9th

I believe this is a fully working tool, but I'm more of a woodworking than a metalworkerDid some light cleaning/metal protect with T-9 Boesheild(I used this when I refurbished old handplanes for cleaning lubing and protection) I think this is from the early 20th century(1900s) The company existed from 1880-1950(Vintagemachinery.org) The handle has a slight angle to it I thought was sloppy at first but now believe it's anintentioner ergonomic improvement, it's rests better in the hand.

Famco 1 arbor press 3/4 ton usa made

Telford, Pennsylvania, United States
Jun 9th

Famco Arbor Press Model No. 1 3/4 ton Made in Wisconsin USA Someone modified this with a piece of aluminum below the bar that presses down, however I think it can be flipped over to use the stock side. Whoever did this also shaped a piece of aluminum to fit in the base's hole.

Very nice 3/8" capacity electric drill by dewalt dw222 w/ keyless chuck

Ellington, New York, United States
Jun 9th

Diacro die holder style a 1-1/4" diameter

Ellington, New York, United States
Jun 9th

1 piece niagara press brake die tooling usa v punch american standard 14"

Ellington, New York, United States
Jun 9th

5 piece niagara press brake die tooling usa v punch american standard

Ellington, New York, United States
Jun 9th

4 vintage cincinniati "c" clamps pre 1927

Helena, Missouri, United States
Jun 9th

First is the big one, The DEEP CLAMP. 3-1/2 X 3-1/2 with the wing nut or butterfly screw. Next is No.

Cooper weymouth scrap chopper

Reading, Pennsylvania, United States
Jun 9th

Used Cooper Weymouth Scrap Chopper S/n CWP16449 6 wide 062 thick 1/3 hp Local pickup or buyer take care of shipping

Greenlee hydraulic electric pump with stand---no reserve

Muncie, Indiana, United States
Jun 9th

GREENLEE---NO RESERVE WILL SHIP---YOUR COST. USED GREENLEE ELECTRIC HYDRAULIC PUMP WITH STAND AND ONE ACCESSORY (((SPREADER JAWS----SUPER HANDY))) IT'S A LITTLE ROUGH, BUT STILL WORKS AS IT SHOULD.HOSES ARE A LITTLE FRAYED, BUT NOT LEAKING. SWITCH IS WRAPPED IN ELECTRICAL TAPE, BUT WORKING FINE.

Di acro 24"shear diacro sharp/ factory/stand material hold down "mint"

Fair Haven, New Jersey, United States
Jun 9th

DIACRO 24" SHEAR THIS IS A 24" SHEAR EXCELLENT ( MINT ) CONDITION/SHARP/FACTORY PAINT /STAND / STANDARD BACK GAUGE/ MATERIAL HOLD DOWN. WE WILL SHIP THIS TO YOUR SHOP , HOME OR FREIGHT TERMINAL NEAR YOU WERE YOU COULD PICK IT UP AT YOUR EXPENSE . JUST GIVE ME A CALL FOR A RATE.

Hand tapper lassy/ral mike's tap and die tapper manual greenlee tapmatic

Fair Haven, New Jersey, United States
Jun 9th

HAND TAPPER RALMIKES WITH TAPS,FENCES AND HAND TAPER. THIS LOOKS LIKE A LASSY 12 TAPPER BUT I CAN NOT FIND A TAG. I PUT IT NEXT TO A LASSY I HAVE AND I COULD NOT SEE ANY DIFFERENCE.

Di-acro roper whitney punch pac #1 / punch & die punch press

Fair Haven, New Jersey, United States
Jun 9th

DIACRO/ROPER WHITNEY/ PUNCH AND DIES. THE SIZES ARE LISTED ON THE PAPER PICTURED PUNCH SHAFT 1/2" DIE 1.25" CALL ME WITH ANY QUESTIONS YOU MAY HAVE! 732-642-8271 VISIT MY STORE :BUFFERS - GRINDER - SANDERSDRILL PRESS

1/4" sheet metal and angle iron

Montgomery, Texas, United States
Jun 9th

Items for sale below: Used sheet metal 1/4" x 48" x 96" minor surface rust $65 Used sheet metal 1/4" x 60" x 96" minor surface rust $75 Used angle iron 4" x 4" x 120" and 4" x 4" x 60" minor surface rust $50 Please call or text to 713-562-7361 for any questions.

Tennsmith 24" slip roll model sr24

Edison, New Jersey, United States
Jun 9th

TENNSMITH 24" Slip Roll Model SR24 Capacity 20 Gage Includes Stand Questions or Shipping Quote call Metro Machine & Tool 732-650-0666

Vintage blacksmith anvil tinsmith anvil jewelry anvil two shaping anvils

Randolph, Nebraska, United States
Jun 9th

TWO OLD BLACKSMITH SHAPING ANVIL'S , THESE CAME FROM BLACKSMITH'S ESTATE , ONE IS DOME TOP AND ONE IS FLAT TOP, COULD NOT FIND MAKERS MARK , DOME TOP IS NICE AND SMOOTH , FLAT TOP HAS SOME SCUFFS AND SCRATCHES , FOR SMALL FORMING , TIN MAKER OR JEWELER'S . 4 IN. TALL DOME TOP 4 1/4 X 2 1/8 IN.

Meyer no. 39 bench top corner notcher made in usa industrial 16 gauge soft steel

San Bernardino, California, United States
Jun 9th

MEYER No. 39 BENCH TOP CORNER NOTCHER MADE IN USA INDUSTRIAL 16 Gauge Soft Steel Questions :Use "A