3 gas pipe for sale, brand-new and used.

Untitled Document Parker® 1/4" NPT Female x 1/4" NPT Female Elbow Brass Instrumentation Grade Manufacture Part No. 1200P-4-4 Swagelok Ref. No.

Untitled Document Swagelok Cajon® 1/16" NPT Male x 1/16" NPT Male Hex Nipple 316 Stainless Steel Instrumentation Grade Swagelok Part. No. SS-1-HN Warning: A 1/16 inch NPT Male pipe fitting, abreviations known as MNPT NPTM MIP MPT MP has an outside diameter of over 1/4 inch.

Untitled Document SSP TruFit® 1/2" NPT Male x 1/2" NPT Male Elbow 316 Stainless Steel Instrumentation Grade Manufacture Part No. ISST8ME Swagelok Ref. No.

GF Piping Systems CPVC True Union Ball Valve, FPM Seal, 1/2" Socket/NPT Threaded. Please see the photos for details of the actual valve. CPVC body for use with temperatures higher than those handled by PVC True union construction for in-place valve replacement Standard port for smaller valve size and reduced cost Inline valve for connecting two pipes going in the same direction Soc

3/4" BLACK MALLEABLE IRON TEE fitting pipe npt - LOT OF 50 3/4-Inch Black malleable tee Black malleable fitting Hydrostatic tested Protected from corrosion with varnish Do not use for drinking water Product Description 312T-34 Diameter: 0.75" Features: -Tee. -Black finish. -All fittings are pressure tested, 150 PSI.

2.0" NPT Pipe Water Meter Golf Course Vineyard Orchard Leak Detection Save #52

(Qty: 2) Metal-Fab B-Vent 3" Diameter Single Wall Flex Connector x 3' Pipe Length - MSWF0303 Metal-Fab's round and oval Type-B vent is listed by Underwriters Laboratories for use with approved category 1 gas furnaces, heaters, and boilers. A category 1 appliance operates with a non-positive vent static pressure. The double wall design of B-vent enables the product to be used in homes and commercial buildings at close clearance to combustible.

(Qty: 6) Metal-Fab B-Vent 3" Diameter Single Wall Flex Connector x 4' Pipe Length - MSWF0304 Metal-Fab's round and oval Type-B vent is listed by Underwriters Laboratories for use with approved category 1 gas furnaces, heaters, and boilers. A category 1 appliance operates with a non-positive vent static pressure. The double wall design of B-vent enables the product to be used in homes and commercial buildings at close clearance to combustible.

This is for a lot of two new old stock 3/4" NPT Brass pipe unions fittings. These are rated for 150 PSI and are good for Water,Oil or Gas. Thanks for looking!

template_preview Portable Manual Car Siphon Hose Gas Oil Liquid Transfer Hand Pump Suction Pipe

Here's another great offer from MP-TRADINGS !! take a look !! I'm listing this time this BOSCH PTZ CCTV system analog surveillance camera.

This Is an Exact Replica Cone Style Muffler For the 2 1/2 - 3 Hp Hp Hercules, Economy, Jaeger, & Arco Hit & Miss Or Throttle Governed Gas Engines Using A 1 1/4" Pipe Thread For the Exhaust !! This is about 8 3/4" In Dia ..... 6 1/4" tall With the pipe 1 1/4 " Pipe thread......

Here is A New Reproduction Muffler for A 1/2 Hp Maytag Upright Gas Engine, This is A Very Good Cast Iron Reproduction, Complete With the Correct Length of 3/4" Black Pipe..... Good Attention to Detail To Make proper fit & Sound, Just like the Original Mufflers.... These Are New, Cast Iron Castings Done Professionally In A Foundry, Then drilled & Threaded On A lathe, Riveted together with 3/16 Rivets Just As The originals were.......

The Apollo 72-100 series two piece inline high pressure ball valve is made of carbon steel and has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made from carbon steel for greater strength and hardness than stainless steel and has a zinc phosphate coating for corrosion protection.

The Apollo series 76-100 two-piece inline ball valve is made of stainless steel and has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of stainless steel for resistance to corrosion and has a stainless steel 304 lever handle with a vinyl sleeve for manual on/off control.

The Apollo 70-100 series two-piece inline ball valve is made of bronze and has a tee-handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of bronze for higher strength and corrosion resistance than brass. Its zinc-plated steel tee-handle for manual on/off control has a compact design and resists accidental turning.