air plasma cutter for sale, brand-new and used.

International Equipment Liquidators eBay Store is a division of EQUIPMENT SERVICE CORPORATION USA This is a Century / Snap-On/ Solar Plasma Cutter Air Pressure Switch. (Part Number 252-003-666). IT FITS Some Century, Solar, and Snap-On, Plasma Cutters.

Product Summary The new AirForce™ 250Ci Plasma Cutter with Built-In Air Compressor features a new lightweight inverter design that is both lightweight and powerful. Built-in compressor for total portability and low system cost. Cuts mild steel up to 1/4in.

Description Plasma Cutter Specs: 208/220vac 50/60HZ Input Single Phase 1PH 50amp cut draws 25Amps 250V No Load Voltage Plasma Cutting: 3" Per minute @ 1" Steel (Severance Cut) 7" Per minute @ 3/4" Thick Steel 17" Per minute @ 1/2" Thick Steel Power Specs: Power Factor 0.93 100% Duty cycle (cut time) at 40amp cut 60% Duty cycle at 50amp cut setting ISO9002 CE, CCC Air requirements: 60-75psi @ 4.5cfm You will have to provide 220V Plug and air supply. What is Included?

HERE WE HAVE: (1) of 12 available. Brand New Gast Oil-less vacuum pump and compressor In original box with manual MSRP $485.00 Model 1531-107B - G289X Motor 220/240

Industrial Equipment Expert, LLC

The D2 is a simple and effective inline compressed air dryer that removes water vapor from up to 7 CFM. The D2 is ideal for protecting a single paint gun, plasma cutter, or pneumatic tool from the harmful affects of wet compressed air. Need help?

The Hobart AirForce 12ci Plasma Cutter features an internal piston-driven air compressor, which makes the system highly portable. No additional compressor to purchase or transport. Pressure is preset, so it's ready to cut, right out of the box.

Selling my AC compressor, been sitting in my closet.

Here is my NEMA 10-30P to 6-50R welding plug adaptor. It allows you to plug a welding machine or plasma cutter with a 6-50 plug into an old 3 prong style clothes dryer outlet. The cord is about 20 feet long, it is a "10ga" cord.

Here is my NEMA 10-50P to 6-50R plug adaptor. It allows you to move the oven and plug in a welding machine or plasma cutter. The cord is about 6 feet long, the lines are both 6ga and the ground is 8ga, that makes it a "6/2 + 8ga" cord.

Only have 3 prong electric range and 3 prong electric clothes dryer outlets at your house, you're not sure which one will power your new machine best and don't want to pay hundreds of dollars to have a welding machine outlet installed? Here is my special non-NEMA 10-50P and 10-30P to 6-50R plug adaptor. It allows you to plug in a welding machine or plasma cutter into a 3 prong electric range OR clothes dryer receptacle.

Here is my NEMA 14-30 clothes dryer plug to common 3 prong receptacle adaptor. This adaptor uses both lines that your hot is hot and your white wire is also hot and green is ground. This adaptor makes it so you can use a common 120 volt 3 prong extension cord to move 220 volt power from one place to another.

Here is my extra long NEMA 6-50 welder and plasma cutter Upgrade cord. It allows you to reach a 3 prong welding receptacle from a good distance with yourmachine. Use on welders, plasma cutters, air compressor.

Here is my extra long NEMA 10-30 clothes dryer appliance cord. It allows you to reach a 3 prong clothes dryer receptacle from a good distance with your clothes dryer or other machine. Use on clothes dryers, welders, plasma cutters, air compressor and small electric stoves.