bolt shaft for sale, brand-new and used.

NEW UNUSED NEW UNUSED WITH FEW SCUFFS,SCRATCHES,ETC FROM WAREHOUSE OUT OF BOX SEE PICTURES. NON ORIGINAL PACKAGING PARKER MODEL: 110A-106-AS-0-F Hydraulic Motor 110A series uses a virtually failure proof single piece shaft.

This is off a machine that never did get used. It's inlet is 1/2" Female NPT and the outlet is a 1/4" male NPT. General Information Case Drain: No Case Drain Inlet And Outlet Ports Size: Manifold Ports 5/16"-18 UNC Thread Geometric Displacement (cu-iIn./rev): 14.10 Output Shaft Size: 1" Straight With Woodruff Key Series: H Series Gerotor Motor SPECIAL FEATURES: Not Listed Type Of Mount: 4 Bolt - 1-3/4" Pilot Dia.

Thomson TWN-16 Linear Pillow Block Bearings 1" Inside Diameter, Heavy-Duty 2,100lb Load Capacity

KLEIN 7 pc. CUSHION-GRIP NUT DRIVER SET 3" SHAFT MODEL #631 MAD

24 volt DC 2.75 " Diameter Motor DUAL SHAFT- NEODYMIUM ...good working condition. 3.8" length. Shaft #1 is 1/2" x 1" w/flat,Shaft #2 is 3/8 x 1/2 smooth.

24 volt DC 3" Diameter Motor,4 brush ...good working condition. 4.55" length. Shaft #1 is 1/2" x 1" w/flat, shaft #2 is 3/8" x 1/2" smooth.

used very little. selling because I had to switch to a ccw pump Product Specifications

Preplumbed and pretested Belt drive Fits 24mm pump shaft Requires 13 HP gas engine; 10 HP electric motor Bolts not included; use existing bolts from old pump to install new pump Key Specs Top of page Item# A1572041 Ship Weight 20.0 lbs Application Pressure washer pump GPM 3 1/2

Move Motor Oil With Confidence Tired of whimpy oil pumps? We've gone through 4 years of development on these pumps. Upgrades have included a custom US Made Baldor motor, viton seals to the pumpheads, scrapping troublesome pressure regulators.

Up for Auction is a Cast Iron Flat Belt Oulley for a Hit&Miss Gas Engine or Line Shaft, Please read discription and Look at all Pictures as they are Part of the discription.

DO NOT DO NOT DO NOT BID ON THIS ITEM IF YOU HAVE EBAY SCORE OF 10 OR LOWER. If you would like to contact us before bidding this will be accepted. Thank you for your understanding.

Industrial Equipment Expert, LLC 5 HP Electric Motor For Comp

This drive shaft is believed to be from an American LaFrance but not guaranteed. The man that had this shaft was a collector of American LaFrance parts. Cant ask him cause he is no longer with us.

Heavy-duty cast iron pump has high pressure capability. Pressure-balanced. Operates at up to 3600 RPM.

New In Box Unused Surplus New Old Stock AO Smith 1/20HP 115V 1550RPM Shaded Pole Open Ventilated Fan & Blower Duty Stock Motor 1.6 amps, 115 volts, 50/60HZ. 1 Speed, 1 Phase,

You are buying TWO (2) matching Adjustable Cast Iron Wood Lathe Jack Shaft Trunnion Supports with thick copper bushings and a spring loaded flip top lubrication port.. Height and attack angle are variable.... Bolt holes are about 2 1/4 inch apart on center Accomodates about a 1/2 inch shaft...

HARD RUBBER WHEELS STEEL HUB BALL BEARING AXLE 5/8" X 9" galv. bolt as axle shaft. lock nuts & washers on the bolts.

Stepper Synchronous motor 72 rpm 120 V Slo-Syn SS250 Unused This is an unused sychronous stepping motor made by Superior Electric, model SS250. Lightly shelf worn paint due to long term storage Bidirectional Start, stop and reverse within 25 milliseconds 72 RPM 250 oz in. @ 72 RPM Step angle: 1.8 degrees, equal to 200 steps per revolution Continuous duty 120 VAC 0.6 A Motor dimensions: OD: 4.21 inches Length: 4 3/4 inches + shaft length Shaft dimensions: Diameter: 3/8 inch Length: 1 3/16 inches