flat shank for sale, brand-new and used.

Brand new, never used 3/16" round-over bit with 1/2" shank. Fits all 1/2" shank portable and table routers. C2 Micrograin tungsten carbide cutting edge provides a good balance of strength and durability.

Brand new, never used 5/32" round-over bit with 1/2" shank. Fits all 1/2" shank portable and table routers. C2 Micrograin tungsten carbide cutting edge provides a good balance of strength and durability.

Brand new, never used 3/8" round-over bit with 1/2" shank. Fits all 1/2" shank portable and table routers. C2 Micrograin tungsten carbide cutting edge provides a good balance of strength and durability.

Brand new, never used 1/4" round-over bit with 1/2" shank. Fits all 1/2" shank portable and table routers. C2 Micrograin tungsten carbide cutting edge provides a good balance of strength and durability.

Brand new, never used 1/8" round-over bit with 1/2" shank. Fits all 1/2" shank portable and table routers. C2 Micrograin tungsten carbide cutting edge provides a good balance of strength and durability.

Brand new, never used 1/16" round-over bit with 1/2" shank. Fits all 1/2" shank portable and table routers. C2 Micrograin tungsten carbide cutting edge provides a good balance of strength and durability.

This is a brand new, never used 3/8" cutting diameter flush trim straight router bit with a 3/8 inch bearing and two carbide flutes. Flush cut bits are used primarily for flush cutting edges to a template, guide or jig. The bearing at the end is of the same diameter as that of the cutting depth so that the cutters will clear all material outside any template the bearing rolls along.

This is a brand new, never used 3/8" cutting diameter flush trim straight router bit with a 3/8 inch bearing and three carbide flutes or blades for superior smoothness, speed, and consistency of cut. Flush cut bits are used primarily for flush cutting edges to a template, guide or jig. The bearing at the end is of the same diameter as that of the cutting depth so that the cutters will clear all material outside any template the bearing rolls along.

This is a brand new, never used 1/2" cutting diameter flush trim straight router bit with a half inch bearing and three carbide flutes or blades for superior smoothness, speed, and consistency of cut. Flush cut bits are used primarily for flush cutting edges to a template, guide or jig. The bearing at the end is of the same diameter as that of the cutting depth so that the cutters will clear all material outside any template the bearing rolls along.

This is a brand new, never used 1/2" cutting diameter flush trim straight router bit with a half inch bearing and 2 carbide flutes or blades. Flush cut bits are used primarily for flush cutting edges to a template, guide or jig. The bearing at the end is of the same diameter as that of the cutting depth so that the cutters will clear all material outside any template the bearing rolls along.

Brand new, never used 10 degree trim and laminate bevel router bit with 1/2" bearing, and a 1/2" shank. Serves for cutting flat faced corner details at 10 (80) degree slope up to 9/16" along the angle. This is basically a 12 degree chamfer bit with a smaller cutting edge for more convenient use in portable routers and in most trim and laminate edging applications where there is no need for more cutting surface Bit fits all 1/2" shank portable and table routers.

Brand new, never used 15 degree trim and laminate bevel router bit with 1/2" bearing, and a 1/2" shank. Serves for cutting flat faced corner details at 15 (75) degree slope up to 5/8" along the angle. This is basically a 15 degree chamfer bit with a smaller cutting edge for more convenient use in portable routers and in most trim and laminate edging applications where there is no need for more cutting surface Bit fits all 1/2" shank portable and table routers.

This is a brand new, never used 1/2" cutting diameter straight router bit with two carbide flutes (blades) and a special gullet between cutting edges that allows for material clearing in mortising applications. The geometry of the blades and the open space between them is designed to allow for clean edge and clear bottom mortising up to about 3/8" depth for shallow hinges.

This is a brand new, never used 1" cutting diameter straight router bit with three carbide flutes or blades for superior smoothness, speed, and consistency of cut. Straight bits are used primarily for clearing dado channels for woodworking joinery, or, in conjunction with a router plate guide bushing or an added shank bearing, for flush cutting slab edges to a template. A 1" bit is also large enough to serve purpose as a surface planer in conjunction with your properly designed router sled.

This is a brand new, never used 3/4" cutting diameter straight router bit with three carbide flutes or blades for superior smoothness, speed, and consistency of cut. Straight bits are used primarily for clearing dado channels for woodworking joinery, or, in conjunction with a router plate guide bushing or an added shank bearing, for flush cutting slab edges to a template. This bit fits all 1/2" shank portable and table routers.

This is a brand new, never used 5/32" cutting diameter straight router bit with a single carbide flute. Straight bits are used primarily for clearing dado channels for woodworking joinery, or, in conjunction with a router plate guide bushing or added shank bearing, for flush cutting edges to a template. This bit fits all 1/2" shank portable and table routers.

This is a brand new, never used 3/8" cutting diameter straight router bit with two carbide flutes or blades. Straight bits are used primarily for clearing dado channels for woodworking joinery, or, in conjunction with a router plate guide bushing or an added shank bearing, for flush cutting edges to a template. This bit fits all 1/2" shank portable and table routers.

This is a brand new, never used 5/8" cutting diameter straight router bit with three carbide flutes or blades for superior smoothness, speed, and consistency of cut. Straight bits are used primarily for clearing dado channels for woodworking joinery, or, in conjunction with a router plate guide bushing or an added shank bearing, for flush cutting slab edges to a template. This bit fits all 1/2" shank portable and table routers.

This is a brand new, never used 5/16" cutting diameter straight router bit with two carbide flutes or blades. Straight bits are used primarily for clearing dado channels for woodworking joinery, or, in conjunction with a router plate guide bushing or an added shank bearing, for flush cutting edges to a template. This bit fits all 1/2" shank portable and table routers.

This is a brand new, never used 3/16" cutting diameter straight router bit with a single carbide flute. Straight bits are used primarily for clearing dado channels for woodworking joinery, or, in conjunction with a router plate guide bushing or added shank bearing, for flush cutting edges to a template. This bit fits all 1/2" shank portable and table routers.