flat shank for sale, brand-new and used.

yes MT1 aka Morse Taper One BIN 6/22 F is all USA Nice MT1 drills as used on Atlas 6 and Myford Lathes @@gen U wine USA !!!@@ --all 100% checked (little or no use) so LOOK ---BUY--COMBINE ~~~~~~~~~~~~~~~~~~~~~~~~~~

yes MT1 aka Morse Taper One BIN 6/22 F is all USA Nice MT1 drills as used on Atlas 6 and Myford Lathes @@gen U wine USA !!!@@ --all 100% checked (little or no use) so LOOK ---BUY--COMBINE ~~~~~~~~~~~~~~~~~~~~~~~~~~

yes MT1 aka Morse Taper One BIN 6/22 F is all USA Nice MT1 drills as used on Atlas 6 and Myford Lathes @@gen U wine USA !!!@@ --all 100% checked (little or no use) so LOOK ---BUY--COMBINE ~~~~~~~~~~~~~~~~~~~~~~~~~~

See all of these NICE USA taper shank drills + combine shipping Combine

LISTING IS FOR A USED TAPER SHANK CORE DRILL

4MM X 40MM 2-FLUTE HRC40 CUTTING SOLID CARBIDE FLAT ENDMILL -10x MATERIAL : SOLIDE CARBIDE SUITABLE TO CUT WORK-PIECE OF HARDNESS BELOW HRC40 2-FLUTE HELIX : 35° RIGHT HAND UP CUT END TYPE : FLAT / SQUARE FLUTE LENGTH : 12MM TOTAL LENGTH : 40MM SHANK DIAMETER : 4MM PROVIDE

8MM X 65MM, 2-FLUTE, HSS, HIGH COBALT %, FLAT, CENTER CUTTING, ENDMILL, 5x MAERIAL : HIGH SPEED STEEL (HIGH COBALT PERCENTAGE) 2-FLUTE CENTER CUTTING TOTAL LENGTH : 65MM FLUTE LENGTH : 21MM SHANK DIAMETER : 8MM 5 PCS IN 5 BOXES THIS ENDMILL MATERIAL CONTAINS HIGH PERCENTAGE OF COBALT. MAKE IT A VERY HARD MATERIAL. IT IS VERY TOUGH, SUPERIOR SHARP CUTTING EDGE.

For sale are new 1/8” (.1250”) three-flute, solid carbide endmills. These endmills called the "VIPER" and are made by Destiny Tool. These tools are probably the best aluminum cutting endmills that I've seen.

For sale are new 3/16” (.1875”) three-flute, solid carbide endmills. These endmills called the "VIPER" and are made by Destiny Tool. These tools are probably the best aluminum cutting endmills that I've seen.

1MM X 50MM 4-FLUTE HRC55 CENTER CUTTING AlTiN/TiAIN CARBIDE FLAT ENDMILL 5x MATERIAL : MICRO-GRAIN SOLID CARBIDE COATING : AlTiN/TiAIN SUITABLE TO CUT WORK-PIECE OF HARDNESS BELOW HRC55 4-FLUTE HELIX : 35° HELIX RIGHT HAND UP CUT END TYPE : FLAT / SQUARE CUTTER DIAMETER : 1MM FLUTE LENGTH : 3MM

1MM X 50MM 2-FLUTE HRC55 CENTER CUTTING AlTiN/TiAIN CARBIDE FLAT ENDMILL MATERIAL : MICRO-GRAIN SOLID CARBIDE. COATING : AlTiN/TiAIN SUITABLE TO CUT WORK-PIECE OF HARDNESS BELOW HRC55 2-FLUTE HELIX :

For sale are five (5) new two-flute, solid carbide endmills. These endmills are 1.00 (.0394") diameter, center-cut endstyle, with a short .120" flute. These tools are normally sold into the printed circuit board market and are made in the USA.

MADE IN USA. For sale are 1/8" (.1250") new two-flute, solid carbide endmills. These endmills are made by Kyocera Tycom.

1/8" X 1-9/16" 2-FLUTE HRC40 CUTTING SOLID CARBIDE FLAT ENDMILL -10x MATERIAL : SOLID CARBIDE NO COATING SUITABLE TO CUT WORK-PIECE HARDNESS BELOW HRC40 2-FLUTE CENTER CUTTING HELIX : 35° RIGHT HAND UP CUT CUTTER DIAMETER : 1/8" TOTAL LENGTH : 1-9/16" SHANK DIAMETER : 1/8"

1MM X 50MM, 2-FLUTE, HSS, HIGH COBALT %, FLAT, CENTER CUTTING, ENDMILL, 5x MATERIAL : HIGH SPEED STEEL (HIGH COBALT PERCENTAGE) NO COATING TWO FLUTES CENTER CUTTING END TYPE : FLAT / SQUARE CUTTER DIAMETER : 1MM TOTAL LENGTH : 50MM FLUTE LENGTH : 3MM SHANK DIAMETER : 3MM TOTAL 5 PCS IN 5 BOXES THIS ENDMILL MATERIAL CONTAINS HIGH PERCENTAGE OF COBALT. MAKE IT A VERY HARD MATERIAL. IT IS VERY TOUGH, SUPERIOR SHARP CUTTING EDGE.

For sale are five new single-flute, solid carbide endmills. These endmills are 1.15mm (.0453") diameter made by Kyocera Tycom. These tools are normally sold to customers cutting acrylic, polycarbonate, and flexible type materials.

MADE IN USA. For sale is a lot of FIVE 1.00mm (.0394") new two-flute, solid carbide endmills. These endmills are made by Kyocera Tycom.