US $469.99
Condition: |
New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is
applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details.
...
|
ISBN | Yusingtools |
Directions
Similar products from Other Workholding Tools
5C HORIZONTAL & VERTICAL COLLET INDEXER NEW
LOT OF CAST IRON EYE BRACKETS, 2"
12 X 12 X 20 SQUARE WORK HOLDING FIXTURE,TOMBSTONE CNC HORIZONTAL MACHING CENTER
Flanged Nut 7/8-9 Flange Nuts Black Oxide Case Harden
ROHM 88065 DRIVING DISC & CENTER
Glaston Bavelloni Diamond Wheel 21915000005 895885 80 M1070 U12.5 150x16x22
Precision 8-200mm Boring Head System+8pcs Borin Bar +R8 Milling ToolHolder Set
Precision 8-200mm Boring Head System+8pcs Borin Bar +BT30 M12 ToolHolder Set
Hilma-Rumheld Hydraulic Hollow piston Single Acting T-Slot Clamping Cylinder
5 - Kipp Pull Knob M12 x 1.5 Indexing Plungers, Non-Locking, 03090-1206, QTY. 5
Dodge 1610x1-1/4" Taper Lock Bushing with 3/8" Keyway. Lot of 2
EARTH CHAIN EZ-LIFT ELM-600 LIFTING MAGNET RATED 1320LB
MAPCO 1 X 2-1/2 PULL DOWELS 5PCS (D201-5)
MAPCO 1 X 3 PULL DOWELS 5PCS (D202-5)
MAPCO 1 X 3-1/2 PULL DOWELS 5PCS (D203-5)
MAPCO 3/4 X 1 PULL DOWELS 12PCS (D188-12)
MAPCO 3/4 X 1-1/2 PULL DOWELS 10PCS (D189-10)
MAPCO 3/4 X 1-3/4 PULL DOWELS 10PCS (D190-10)
People who viewed this item also vieved
KENNAMETAL ERICKSON COLLET 19/32 UNUSED FROM OLD STOCK. SB6
SANDVIK TAP DRIVER COLLET 22098-20.32-.800
Machinists Suburban Sine Plate In Box 12 x 6 x 2 5/8
Used 30" x 21.25" x 44" tall tombstone
2 SETS OF MACHINIST PARALLEL CLAMPS set up hold down work holder 2" & 2-7/8"
LARGE USED MACHINIST PARALLEL CLAMP 6" Jaws 4" Capacity metal work holding tool
Pair 6” Deep Kant Twist Clamps
C12 ER11A 150L Straight shank & ER11A wrench Collet Chuck toolholder CNC Lather
21" WARNER & SWASEY, 4-JAW CHUCK, M-1614-9, T & G JAWS, 6.5" HOLE, A2-11
27.5" 4-JAW MANUAL CHUCK, TM, 10.25" HOLE, ONE PIECE JAWS, A2-11
Wilton Drill Press Press 6" Jaw Width 6 1/2" Clamp Width Bench Machinist Tool
WILTON Combination VISE, C0, 3 1/2' JAWS, PIPE JAWS, IN EXCELLENT CONDITION
Ridgid F Series Forged Steel Bench Swivel Vise 6" Jaw Width Machinist
ROYAL Quad-Bearing Live Center Point Length : 1-1/16'' Overall Length : 6-7/16''
ROYAL Value-Turn Live Center Point Length : 7/8'' Overall Length : 5-7/8''
BISON Ultra Precision Adjustable Heavy Duty Live Center Point Length : 2.44''
Weiss TC-700-T (B) Rotary Indexing Table (2011) w/Lenze-based PLC Control
large Indexing Dividing Head L-W Chuck Co. Toledo Ohio USA WITH CHUCK
25" Troyke T-slotted Rotary Table Model BH-25
MACHINIST LATHE MILL Machinist Ground Hold Down Block Fixture for Set Up NICE
MACHINIST LATHE MILL Machninst Large Ground Set Up Block Fixture Step Block
MAGNETIC V BLOCK, 2 SIDED - 1" & 2"
ETM ER40 Collet Chuck ST1.000X2.375 ER40 Holder
Hertel HCV50ER32400 Collet Chuck Series ER-32
B&V collet chuck 20 MM w/ case
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
Accept All Cookies