shaft wheel for sale, brand-new and used.

This cycle wheel is made by me and has a 1 3/4" plastic knob and left hand 6-32 threads for screwing into the operational shaft of the IBM Selectric. I have used a less expensive knob than my other models but it's plenty hefty for the hand cycling job and long enough to fit into the op shaft while the machine is still in the bottom cover.

Hi, this is Don. I removed this set of wheel retainers from a very old grinder that was 10" stone, 1 hp, 440v, 3ph. It had a label that said, "Hisey", but I noticed the fenders were of the exact same construction as my antique 8" Cincinnati grinder, so I'm assuming that these parts may fit the old Cincinnatis as well.

This counter can measure to 9,999 feet.

Used Wheel Chair Motor with gear assy. NOTE: Not intended as a replacement for wheel chair. But as hobby use or battle bot Motor has been bench tested and runs fine.

(4) Colson "Total Lock" 5" x 1.25" Swivel Casters 325 Lb Capacity Per WheelMiniTec Part # 21-9404 / Colson Part # 2.05256.441LOT OF 4 Lot of 4 casters as described above. See pictures and link below for more details. Compare at over $35.00 each."Total Lock " casters lock both wheel ro

Wheel Arbor Assembly for Dumore Tool Post Grinders.Converts 3/8" x 24 grind wheel shaft to 1/4" grind wheel shaft.Included in Series 44 Tool Post Grinders.Will also work on Series 57 type "B" or 5X-250 Spindles I spun the tool to about 15,000 RPM, and it appeared to be straight and true. I have not tried grinding with it. Used grind wheel in picture included.

discount

SEE MY OTHER LISTING FOR THE COMPLETE FAN WITH MOTOR EBAY # 221698786532 .... THIS IS THE WHEEL THAT IS IN THOSE FANS...THIS WHEEL IS STEEL AND HEAVY DUTY...4 1/2 LBS.

One tire and wheel combo.Solid rubber tire removed from Go-Go mobility scooter.2" wide X 8 " tall 5/16" axle bore with roller bearings.Small axle included. Good for heavy duty wheeled project. Thanx for looking.

Item is unused in non original package  Includes washer and instruction manual 1/2" shaft diameter , minimum 2" flange diameter

Model:PSMW28Internet/Catalog:

Up for bid is a set of 2 colson swivel lock wheel, all measurements are close. (wheel size 5in.) (wheel width is 1-.1/4) ( shaft height 2 -3/4) ( shaft width 1 -in.) ( total height from top to bottom 8.-3/4 in.) please ask any questions thank you for looking.

Version Francaise au bas. Hi You are bidding on one used bidirectional gearmotor similare to picture # 2 , MVA gear box 10 to 1 and FMC magnetic brake 2.5 Nm in good working condition. Motor is a 861L Leroy Somer permanent magnet brushed motor.

Welcome to my listing Bienvenue sur mes annonces Version Francaise au bas. Hi Here for sale one good used bidirectional gearmotor similare to picture # 2 , MVA gear box 10 to 1 and FMC magnetic brake 2.5 Nm in good working condition. Motor has never been abuse since it only was used with a controller and that can be seen by the little brush commutator inspection port.

Package Includes 1 Piece - gear dc motor 12v-24v MFG: MOLON P/N: CHM-2435-1

This lot is comprised of a half inch straight shaft spindle w/ a tapered end, mated with a 6 inch extension for a polishing head with a 5/8 shaft... The balance of the lot is an assortment of used and old stock finishing wheels. The scotch brite type (3M) flap wheel and 2 wire wheels have a 2 inch core.