arbor plates for sale, brand-new and used.

Your No. 1 Choice for Press Accessory Solutions We have 6 of these stocky little bars (THE GUY'S IN THE BACK CALL THEM "BITTY BARS") measuring 1" X 3/4" X 4.25”, in our shop. They were designed for use on our 6 Ton Famco arbor press where they support 12000 lbs.

These bars were designed for use on 2 Ton arbor presses where they easily support 4000 lbs. over the anvil wheel slot span of less than 1.42”. They are also useful as bench blocks, shims, and set-up blocks.

These bars were designed for use on our 1 Ton Palmgren arbor press where they easily support 2000 lbs. over the anvil wheel slot span of less than 1.25”. They are also useful as bench blocks, shims, and set-up blocks.

These 3 Ton Press Bars used flat (4 Ton used on edge), measuring 1/2" X 3/4" X 4.25, were designed for use on a 3 ton arbor press where they support 6000 lbs. over the anvil wheel slot span of 2” or less. These FULLY GROUND matched bars are handy for other uses such as set-up blocks and shims.

This tiny 4 piece press bar set measures 1/4" X 1/2" X 2" long. These were designed for use on a .5 ton arbor press where they support 1000 lbs. over the anvil wheel slot span of less than 1.06.” Edges are Hot Rolled Mill Finish, with scale, and are not ground.

We have 4 of these stocky little bars (THE GUY S IN THE BACK CALL THEM "BITTY BARS")measuring 1"X3/4" X 4.25”, in our shop. They were designed for use on our 6 Ton Famco arbor press where they easily support 12000 lbs. over the anvil wheel slot span of less than 2.75” They often find themselves over on the 30 ton “H” frame press as set-up blocks, blocking, or load spreading blocks in heavy load situations.

Amp/Tyco Electronics 126840-1 Tooling for Manual Frame Assembly

PLEASE view all 8 Photos, read the condition report & measurements below and ask any questions you may have BEFORE bidding. DESCRIPTION: Up for auction is this 8 piece expanding arbor set with 4 allen wrenches all in an organized solid wood block. From what we read online you would use these by chucking the shank of the expanding mandrel in a collet, jaw chuck or fixture.

Totally restored Famco #1 3/4-ton rated arbor press. This is the third one I've done and I know these presses inside and out. The unit has been stripped down to smallest individual parts, de-greased, de-rusted with a chelating solution for long-term protection, primed, and painted with high temperature VHT wrinkle paint on all surfaces including the bottom, then oven-cured at 175° for two hours for a durable finish.

Totally restored Famco #1 3/4-ton rated arbor press. This is the third one I've done and I know these presses inside and out. The unit has been stripped down to smallest individual parts, de-greased, de-rusted with a chelating solution for long-term protection, primed, and painted with high temperature VHT wrinkle paint on all surfaces including the bottom, then oven-cured at 175° for two hours for a durable finish.

Totally restored Famco #0 1/2-ton rated arbor press. This is the third one I've done and I know these presses inside and out. The unit has been stripped down to smallest individual parts, de-greased, de-rusted with a chelating solution for long-term protection, primed, and painted with high temperature VHT wrinkle paint on all surfaces including the bottom, then oven-cured at 175° for two hours for a durable finish.

Replacement arbor nut for a Delta Unisaw table saw. This is a "new" machined arbor nut to secure the saw blade in a Delta table saw. Several hundred have been manufactured and sold in the last two years.

Thousands of Used Metalworking and Plastic Machines & New Machine Tools Photos, Full Descriptions and Prices - Fast & Easy