1 2 ton arbor press for sale, brand-new and used.

Jet 3 ton arbor press .... I am selling New/other , this item has not been used please look at the pictures , look at the bottom of the ram no indications of use .. The press has some scuffs on it plus the red lever lock in the first picture , will lock the handle but the part you grab on is broken, its a plastic knob .

Wilton & JET Equipment 333650 - Arbor Press 5 Ton For all Production and assembly applications. Precision cut steel rams and pinions for accurate operation. Tables and slotted table-plates are flat and parallel to provide accurate support.

These bars were designed for use on our 1 Ton Palmgren arbor press where they easily support 2000 lbs. over the anvil wheel slot span of less than 1.25”. They are also useful as bench blocks, shims, and set-up blocks.

These 3 Ton Press Bars used flat (4 Ton used on edge), measuring 1/2" X 3/4" X 4.25, were designed for use on a 3 ton arbor press where they support 6000 lbs. over the anvil wheel slot span of 2” or less. These FULLY GROUND matched bars are handy for other uses such as set-up blocks and shims.

We have 4 of these stocky little bars (THE GUY S IN THE BACK CALL THEM "BITTY BARS")measuring 1"X3/4" X 4.25”, in our shop. They were designed for use on our 6 Ton Famco arbor press where they easily support 12000 lbs. over the anvil wheel slot span of less than 2.75” They often find themselves over on the 30 ton “H” frame press as set-up blocks, blocking, or load spreading blocks in heavy load situations.

Up for sale is a FAMCO ARBOR PRESS MODEL A. I believe it is 1/2 ton capacity. 3/4" square ram.

var itemNumber = window.ebayItemID ?

Your No. 1 Choice for Press Accessory Solutions We have 6 of these stocky little bars (THE GUY'S IN THE BACK CALL THEM "BITTY BARS") measuring 1" X 3/4" X 4.25”, in our shop. They were designed for use on our 6 Ton Famco arbor press where they support 12000 lbs.

Dake Arbor Press no 1 1/2 in great condition and working order. Just dusty from storage. Comes with the pedestal.

This tiny 4 piece press bar set measures 1/4" X 1/2" X 2" long. These were designed for use on a .5 ton arbor press where they support 1000 lbs. over the anvil wheel slot span of less than 1.06.” Edges are Hot Rolled Mill Finish, with scale, and are not ground.

Note regarding fit: Measure your inside, front to back, bed gap. These 4 bars are intended for stand alone use on 20 ton presses with, front to back, gap of about 4.25". Your No.

Sale is for One (1) USED JET PRESS MODEL MAP-2 ARBOR PRESS 2 TON BENCHTOP LEVER PRESS Item has light scratches shown in the photos This press only comes with what is shown in the photos The one shown in the photos is the one you receive Specs; Manufacturer-

You are considering a Jet 5-ton manual arbor press. This press is used, but is in good overall condition. Looks as though the previous owner had painted it recently.

ORIGINAL DAKE 1 1/2 TON ARBOR PRESS WITH ADAPTER BASE PLATE.VERY SMOOTH OPERATION (VERY HEAVY) !! ORIGINAL PAINT, FROM A ESTATE CLEAN-OUT WE DID. HARD TO FIND IN THIS CONDITION.

This 4 pc set is now being offered with our PREMIUM X-BARS. Note regarding fit: Measure your inside, front to back, bed gap. These 4 bars are intended for stand alone use on 20 ton (or less) presses with, front to back, gap of about 4.25 inches.

Totally restored Famco #1 3/4-ton rated arbor press. This is the third one I've done and I know these presses inside and out. The unit has been stripped down to smallest individual parts, de-greased, de-rusted with a chelating solution for long-term protection, primed, and painted with high temperature VHT wrinkle paint on all surfaces including the bottom, then oven-cured at 175° for two hours for a durable finish.